Jump to content
SAU Community

Recommended Posts

Hey guys.

Went for the tune of my 25/30. We cant get it to make hardly any power. And compared to my old slap together SOHC setup, it makes less power less torque and it all happens later, Also its starting to knock up high at anything over 19psi (98ron).

We suspected cam timing so degreed the cams in again, (found the exhaust cam 15 degrees retarded). intake cam is 4deg retarded but cant adjust that with out pulling the gear off.

Set the exhaust back to 115 deg *standard cams. It made it better but not a whole lot better.

Motor specs

Rb25/30 Neo 9:1 comp (old motor was in the 7s)

forged pistons, rods

CPC plenum

steam pipe manifold gt35

3inch exhaust 1 muffler no cat

660cc injectors

vipec v88

Standard head with upgraded springs and retainers

still has vct but didnt turn it on yet.

Exhaust, turbo and intercooler plumbing is exactly as it was on old motor.

Here's a pic of the run in comparison to the old sohc.

Any ideas?

post-78438-0-27124000-1429354860_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/455838-new-motor-making-no-power/
Share on other sites

Hate that! I'm tipping you had mentally prepared yourself for a big increase! Not that a forged engine will necessarily make more power, just stay together for a bit longer.

I would presume they have checked spark timing?

How confident are you of the compression ratio?

How long has the car been sitting during rebuild- not old stale fuel?

Not sure if it's possible but VCT not locked over advanced seeing not connected?

I'm sure there are other possibilities but that's all I can think of. The knock is a concern and hopefully leads to the diagnosis. It shouldn't be pinging on 98 with 9:1 comp.

Good luck!

Well yeah I was looking for at least an extra 30-50 hp. Going from a single cam head to a twin cam head.. The single cam head only had a baby cam. I expected the boost and power to be on earlier and make more torque and power in general.

Yeah we double checked ignition timing. Pretty confident on the comp, its a tad higher then 9:1 i have it here somewhere.

Fresh fuel. And Ive done over 1000ks on the motor with a soft tune.

Not sure on the vct one but I thought if off its just normal and energized it will advance? Even being advanced you would think the power would be on alot sooner

Ok not sure where to go next with this thing.

Got the cams set at In 121. Ex113

Gets to about 5000rpm and starts detonating even with only 13 degrees timing on only 17-18psi, still making no power or torque.

Afr are good

Compression is 170-165 across all 6.

It has around 2.5 psi exhaust back pressure

And 2.5psi pressure drop from hot side to manifold

Head was decked down to 46cc to get the comp up a bit.

To much compression?

Is it possible the vct gear is stuffed and causing the cam timing to move around?

Is it me just getting old but are those pistons dished in the picture?

I hope not because if they are i can assure you your not getting 9:1 compression.

For some reason i see a 5-9mm ring at deck height around the piston, then they dip down lower.

Is that right?

If so then i can see lots of Det causing pockets right under the quench pads.

Did you round off the valve relief edges on the pistons?

Its a really weird piston shape for those heads, what pistons are they? Part number?

Maybe they are domed, im seeing dished, could be the way the pic was taken......

Cam's can only go one way due to the VCT gear on inlet.

Yeah you are seeing correctly, they are dished. 9cc. (Dished because neo chamber is alot smaller than the normal 25-26 head

They are a wiseco piston, here is a close up. Did not do anything with the pistons...

It's seeming more likely these are the issue with the knock.

post-78438-0-18039900-1430036937_thumb.jpg

Edited by Huzqld

I'm pretty confident on the compression, calculated while we were building.

Is there anything I could get done to the head to fix the issue?

Really don't want to have to pull the motor back out to replace Pistons and get it all balanced again. I think if I have to go that far I'll put a 26 head on it while it's out.

post-78438-0-85664600-1430043134_thumb.jpg

How sure are you about the 9:1 compression? You planed the head to get the compression up and then dished the pistons to get it down? Do a compression reading and see what you get

I don't know what your cam settings are - they seem a prime suspect.

I already had the pistons as I bought all the parts off a guy that didn't go ahead with a build. I was going to just run somewhere in the 8:1 range compression but was advised against it, so decked the head to get to 9:1.

Did a compression test and got 170-165 PSI across all 6

Cam settings are. Inlet 121deg- Exhaust 113deg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...