Jump to content
SAU Community

Recommended Posts

Mike,

Got my package of headlights yesterday on the doorstep.

Thank you for the time and effort taken to wrap and box everything, it was better than Christmas.

To the rest of SAU, this guy is awesome.

Adam

Thanks for the feedback Adam. Glad you are happy

RB25 (without microtech), taiulshaft to suit 25 in 32, front strut brace, and whiteline sway bar - all SOLD

Also worked out that the other RB25 with microtech is actually series one. I had assumed since no ignitor that it was series 2, however after looking at the TPS (its only single fixed plug, with the second plug below on its own wiring - same as RB20) it appears that it is series one, running series 2 coilpacks due to the microtech etc.

All PM's replied.

Also have standard RB25 series 2 unchopped/unmodified loom and computer available.

R32 exhaust as well. No front pipe though.

And R32 GTR turbos

I will open it up tmrw and find out. I'll let you know

I just took the diff out of the car. Its 4.3 ratio (48:11) and def 2 way - can provide photos Crown and pinion gears are perfect, however bearings have a bit of slop and i would recommend replacing. Price drop to $450 because of bearings etc.

All PM's replied.

Also have standard RB25 series 2 unchopped/unmodified loom and computer available.

R32 exhaust as well. No front pipe though.

And R32 GTR turbos

Is that an R32 3' catback exhaust?

GTR intercooler - SOLD

Rear strut brace - SOLD

RB25 tailshaft - SOLD

Price drop on remaining RB25 - Series 1 motor, full loom and microtech computer, adj cam gear, perfectly good running motor. Have video of it running. No turbo, p/s pump or air con compressor. - $1200 neg

  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...