Jump to content
SAU Community

Recommended Posts

right perchased my stagea 2 weeks ago converted to manual last week upon taking it out on a test drive ran like crap idle wasbad from when i got it sometimes hunts or dies when coming to a stop i realize that that could be aac but i thought i had better check whats going on so installed wide band calibrated it at idle its at 17 then go for a gentle short drive stays about 17 not going into boost because of this.... plus no power really at all...

when driving back when it was auto noticed a strange flatspot where you would let of a tad then go back on it would jerk

checked for dry solder in the maf (pink e60) nothing completely fine no boost leaks before the turbo has a hybrid turbo good for around 550bhp 550 side feed injectors 1.6mm hks head gasket mines ecu. also fitted nkg spark plugs at standard gap i know this can be a problem on some turbo applications but surely not going to cause lean conditions ?

im a novice with Nissans any help would be fantastic thanks

Link to comment
https://www.sau.com.au/forums/topic/456509-my-stagea-issues/
Share on other sites

You can't check for dry solder joints without a microscope, did you simply resolder the pins?

Sounds like you may need a tune, the Mines could be setup for any mods...

not soldered yet but will do. also yes i know thinking of going fully aftermarket but if i do will i run into complications with attesa system ?

Edited by centoproject

No, why would you? There are literally hundreds of tuned Stagea's getting about, why would you think they are all in RWD?

I think you should do some in depth reading, search for similar issues, speak to a few tuners locally and come to your own conclusions as to what will work best. Now you have gone manual perhaps a Standalone ecu is your best bet, but you have so many options with the RB25

No, why would you? There are literally hundreds of tuned Stagea's getting about, why would you think they are all in RWD?

I think you should do some in depth reading, search for similar issues, speak to a few tuners locally and come to your own conclusions as to what will work best. Now you have gone manual perhaps a Standalone ecu is your best bet, but you have so many options with the RB25

oh i see well i have done quite a lot of research but they all could be the problem so i will go at one at a time my main question was what are the main components that fail as a hole as apposed to someones idle being iffy mine seams to have quite a few issues ?

Because your ECU has someone else's tune on it no doubt. The more you mod it, the worse it will get.

hmm the ecu was installed by a tuner over here in England along with a load of other stuff (supporting mods) im trying to track down the original uk owner for more info but he spent a hell of a lot on this paperwork says that it had nistune installed but had a look yesterday and mines ecu with the gold plate

also whats the best ecu that can fit in the stagea without cutting looms ect plug and play i know a lot wont fit only mines and nistune

Most ecu will need a little bit of rewiring but best one to get in the UK for a manual Stagea is a link G4. You can also get rid of the maf while your at it. Have a G4 myself and can't fault it.

I'm sure once you have an ecu with a proper tune you will have no more problems!

The attesa connects to the ECU via 3 wires:

ATTESA pin -> ECU pin - Description

Pin 3 -> Pin 5 - Tachometer signal

Pin 23 -> Pin 37 - TPS

Pin 34 -> Pin 43 - Sensor ground

Thankfully the unit can be used quite independently. If you feed it a pull-to-ground tach signal, it should function without throwing an error code and turning off the 4WD.

If you are delving into different ECUs, the voltage drop associated with sensors like the TPS will influence what the 4WD thinks your actual throttle amount is. If you have some skill in electronics, you should be able create your own circuit to bend the TPS as you wish.

If not, you should probably learn.....the S1 can be a headache to tune.

The attesa connects to the ECU via 3 wires:

ATTESA pin -> ECU pin - Description

Pin 3 -> Pin 5 - Tachometer signal

Pin 23 -> Pin 37 - TPS

Pin 34 -> Pin 43 - Sensor ground

Thankfully the unit can be used quite independently. If you feed it a pull-to-ground tach signal, it should function without throwing an error code and turning off the 4WD.

If you are delving into different ECUs, the voltage drop associated with sensors like the TPS will influence what the 4WD thinks your actual throttle amount is. If you have some skill in electronics, you should be able create your own circuit to bend the TPS as you wish.

If not, you should probably learn.....the S1 can be a headache to tune.

thanks fellas yes the s1 seams to be nightmare at the moment aftermarket should solve my problems no end as for tps related things i have done a search but no luck on the voltage adjustment of the actual tps i have seen people mention this ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...