Jump to content
SAU Community

Recommended Posts

Hi there,

This maybe my first post, so please help me out here.

I recently acquired a 1996 Nissan Skyline R33 GTS 4 door that HAS NOT run for 3 1/2 years.

I have drained the fuel tank, changed the fuel and air cleaner elements.

A new battery has also been installed.

It cranked up and fired into life after a little coaxing. It ran for a few minutes and then I switched it off and changed the oil and oil filter.

Now the engine will not fire up again.

Since changing the fuel filter and air filter, the fuel no longer flows!

There is NO clicking of any relays and NO noise from the pump.

I have checked under the bonnet fuse box and FUEL PUMP fuse is serviceable.

The fuse box under the dash has ALL serviceable fuses.

Problem is, it is all in JAPANESE!

The Google search did not help for the translation as the detailed page dose not match up with the Amp rating or layout of IGN, ACC or BATT.

My main questions are:

1/. The relays are quoted to be inside the boot between the tail lamps under the boot catch assy

They are not there!

Where would they be?

2/. Is there any wiring mods that I can do simply that will get the pump running?

3/. As per Q2, can I put in a HOT wire and run the pump via a relay I supply and trigger it from existing switching wire>

I would like to see this car up and running tomorrow if I can find some quick and easy to do solutions.

Many thanks in advance..

Edited by PranK
Changing 'R32' to 'R33'
Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/
Share on other sites

I just bought a "barn find" r34 and it had the same problem - turned out to be a dud connection on the positive battery terminal. Was cranking fine with a new battery, had all the ignition lights, just not enough current for the fuel pump

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7533348
Share on other sites

Is said barn red?

Seriously though, start from one end of the system and work through. Power to ecu, power to trigger wire, power to pump relays, which should be under the parcel shelf, next to the battery IIRC, power to tank lid connection etc. (I'm pretty certain i got that order right... been fighting the flu for the past 24 hours and the brain is a bit foggy)

If all is dandy, pump itself may be rooted. Sitting in stale fuel for 3+ years will clog it up with varnish pretty fast. Did you clean the tank out or just drain it? Prick of a job to do in a 33

I thought My bosch 040 had died a while ago, and after replacing the pump, it actually turned out to be the pump trigger wire burnt out from another unrelated issue.

As per Q2 and 3, you can do both, but both won't work if there's another wiring issue, or the pumps is rooted, unless you simply hardwire from the battery to the tank lid connection.

Hope that helps you in any way.

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7533911
Share on other sites

  • 2 weeks later...

Hi

Still have NO POWER to pump.

Checked all fuses and swapped relays.

ZILCH

Connected 12volts direct to pump and turned key YOU BEAUTY! .....................IT RUNS!

Will now trace and find the break.

If not, should I supply 12volts from battery direct to a relay AND switch it from ignition side of fuse box??

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7538470
Share on other sites

Could be a few thing but the three most obvious to me are 1) the fuel pump control module which povides the amperage to the pump which is control with the signal from the ECU, 2) the fuel pump relay on the back wall of the truck, 3) the alarm which should be spliced into the fuel control signal from the ECU to cut that signal so the pump doesn't activate

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7538661
Share on other sites

I just went through this on another car. My problem turned out to be a bad ground wire AND a faulty pump! Sometimes the ground was there, sometimes it wasn't. Sometimes the pump ran, sometimes it didn't (internal fault in pump) Check the ground wiring and bang on the fuel tank, doing so might make the pump run, which if it does you know the pump is faulty.

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7539205
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
    • Well, I had an Edward Lee's special edition odo windback car/motor with a RB25DET S2 and I put down 372kW with a good amount of track abuse for 1.5 years before the ring lands decided it didn't want to stick around anymore 🥲 But probably didn't help I kept on smashing try limiter on the track and a few skid pans.
×
×
  • Create New...