Jump to content
SAU Community

R33 Barn Find

ScruffyR34
 Share

Recommended Posts

ScruffyR34 Rookie

ScruffyR34

Posted
Posted (edited)

Hi there,

This maybe my first post, so please help me out here.

I recently acquired a 1996 Nissan Skyline R33 GTS 4 door that HAS NOT run for 3 1/2 years.

I have drained the fuel tank, changed the fuel and air cleaner elements.

A new battery has also been installed.

It cranked up and fired into life after a little coaxing. It ran for a few minutes and then I switched it off and changed the oil and oil filter.

Now the engine will not fire up again.

Since changing the fuel filter and air filter, the fuel no longer flows!

There is NO clicking of any relays and NO noise from the pump.

I have checked under the bonnet fuse box and FUEL PUMP fuse is serviceable.

The fuse box under the dash has ALL serviceable fuses.

Problem is, it is all in JAPANESE!

The Google search did not help for the translation as the detailed page dose not match up with the Amp rating or layout of IGN, ACC or BATT.

My main questions are:

1/. The relays are quoted to be inside the boot between the tail lamps under the boot catch assy

They are not there!

Where would they be?

2/. Is there any wiring mods that I can do simply that will get the pump running?

3/. As per Q2, can I put in a HOT wire and run the pump via a relay I supply and trigger it from existing switching wire>

I would like to see this car up and running tomorrow if I can find some quick and easy to do solutions.

Many thanks in advance..

Edited by PranK
Changing 'R32' to 'R33'
Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/
Share on other sites
junkie Mentor

junkie

Posted
Posted

I just bought a "barn find" r34 and it had the same problem - turned out to be a dud connection on the positive battery terminal. Was cranking fine with a new battery, had all the ignition lights, just not enough current for the fuel pump

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7533348
Share on other sites
R31 drift pig Experienced

R31 drift pig

Posted
Posted

Is said barn red?

Seriously though, start from one end of the system and work through. Power to ecu, power to trigger wire, power to pump relays, which should be under the parcel shelf, next to the battery IIRC, power to tank lid connection etc. (I'm pretty certain i got that order right... been fighting the flu for the past 24 hours and the brain is a bit foggy)

If all is dandy, pump itself may be rooted. Sitting in stale fuel for 3+ years will clog it up with varnish pretty fast. Did you clean the tank out or just drain it? Prick of a job to do in a 33

I thought My bosch 040 had died a while ago, and after replacing the pump, it actually turned out to be the pump trigger wire burnt out from another unrelated issue.

As per Q2 and 3, you can do both, but both won't work if there's another wiring issue, or the pumps is rooted, unless you simply hardwire from the battery to the tank lid connection.

Hope that helps you in any way.

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7533911
Share on other sites
  • 2 weeks later...
ScruffyR34 Rookie

ScruffyR34

Posted
  • Author
Posted

Hi

Still have NO POWER to pump.

Checked all fuses and swapped relays.

ZILCH

Connected 12volts direct to pump and turned key YOU BEAUTY! .....................IT RUNS!

Will now trace and find the break.

If not, should I supply 12volts from battery direct to a relay AND switch it from ignition side of fuse box??

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7538470
Share on other sites
XKLABA Grand Master

XKLABA

Posted
Posted

Could be a few thing but the three most obvious to me are 1) the fuel pump control module which povides the amperage to the pump which is control with the signal from the ECU, 2) the fuel pump relay on the back wall of the truck, 3) the alarm which should be spliced into the fuel control signal from the ECU to cut that signal so the pump doesn't activate

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7538661
Share on other sites
T-Rex Enthusiast

T-Rex

Posted
Posted

I just went through this on another car. My problem turned out to be a bad ground wire AND a faulty pump! Sometimes the ground was there, sometimes it wasn't. Sometimes the pump ran, sometimes it didn't (internal fault in pump) Check the ground wiring and bang on the fuel tank, doing so might make the pump run, which if it does you know the pump is faulty.

Link to comment
https://www.sau.com.au/forums/topic/456597-r33-barn-find/#findComment-7539205
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • isf
      HR34 GT speedo issue

      By isf · Posted

      The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Mine's a bit bigger at 70x150mm roughly. The spots are flat, just can feel the edges if I dig my nail into it. I did fix some other other ones by both using my finger to sand that small spot (I'm a bit wary of doing this and creating hot spots and a bigger mess) and I also did sand over it flat and others, but this also worried me a bit because if I create an overall low spot on the panel on paint that is good.  Correct me if I'm wrong but as long as it's flat even if I can feel the edges, I can put filler because it will all be level once I sand it? I can see myself going in a circle after sanding guidecoat with 320 grit if for example the panel is flat with my hand but because I sanded the guidecoat I could have created a low spot again somewhere. Unless where I'm going wrong is what I mentioned previously where I didn't go low enough on the grits. It's 1 step forward and 2 step backwards here haha. I'll probably need to experiment with it more. Last time I go back to bare metal lol.
×
×
  • Create New...