Jump to content
SAU Community

Recommended Posts

15 minutes ago, Manne said:

you need your receipt or a bank statement so  we can get your receipt. If you don't have your receipt, you'll need to go to the store of purchase as other stores wont have access to it.

So if I don't have receipt I can still just bring the item back and they can trace it...as long as it was from the store I bought from yea?

Thanks man

1 hour ago, Manne said:

you need your receipt or a bank statement so  we can get your receipt. If you don't have your receipt, you'll need to go to the store of purchase as other stores wont have access to it.

so now if Colin doesnt come to see you, youll know hes been cheating on you and going to another store :15_yum:

@z00key i think i was telling you @racewars about one of the apprentices at work having an old crappy looking EL that went hard and had all the driveline break and then replaced to handle the engine after he turboed it. 

 

today i found out he was actually there. his was a goldy/champagne coloured one. 262km/h over 1000m. 33rd fastest

  • Like 1
1 hour ago, colin.ssc said:

So if I don't have receipt I can still just bring the item back and they can trace it...as long as it was from the store I bought from yea?

Thanks man

No, you need the receipt or a bank statement. 

48 minutes ago, t_revz said:

so now if Colin doesnt come to see you, youll know hes been cheating on you and going to another store 

Lol, asking for the gf, her house modem died, they cant find receipt. oh wells sucks to be them.

10 hours ago, t_revz said:

@z00key i think i was telling you @racewars about one of the apprentices at work having an old crappy looking EL that went hard and had all the driveline break and then replaced to handle the engine after he turboed it. 

 

today i found out he was actually there. his was a goldy/champagne coloured one. 262km/h over 1000m. 33rd fastest

good work, I recall you saying this.

11 hours ago, t_revz said:

@z00key i think i was telling you @racewars about one of the apprentices at work having an old crappy looking EL that went hard and had all the driveline break and then replaced to handle the engine after he turboed it. 

 

today i found out he was actually there. his was a goldy/champagne coloured one. 262km/h over 1000m. 33rd fastest

Yeah I remember you saying that wondered if that was the guy who was taking the mickey out of him saying its one of the fastest taxis in WA lol. I also am having a few issues with the app (but android)

11 hours ago, z00key said:

Yeah I remember you saying that wondered if that was the guy who was taking the mickey out of him saying its one of the fastest taxis in WA lol. I also am having a few issues with the app (but android)

the funniest thing about his upgrades is that the transmission is controlled by 2 toggle switches in the centre console. 

both on to stall up, turn off one to get 1st. then both off for 2nd, one back on for 3rd etc etc. so simple yet dodgy :)

  • Like 1



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...