Jump to content
SAU Community

Recommended Posts

If you're actively working as one, I'd love a quote on my skyline.

Unfortunately not any more.
I left many years ago but have painted a few cars at home for family. Last one was shoey87 nissan pulsar sss with a sr20det conversion. One befor that was my dads triumph sprint 1977 full reso running a sr20det. Both where flow coated and came out like glass
  • Like 1
1 minute ago, Shoey84 said:


Unfortunately not any more.
I left many years ago but have painted a few cars at home for family. Last one was shoey87 nissan pulsar sss with a sr20det conversion. One befor that was my dads triumph sprint 1977 full reso running a sr20det. Both where flow coated and came out like glass

Fair enough :96_ok_hand:

1 hour ago, Shoey84 said:


Unfortunately not any more.
I left many years ago but have painted a few cars at home for family. Last one was shoey87 nissan pulsar sss with a sr20det conversion. One befor that was my dads triumph sprint 1977 full reso running a sr20det. Both where flow coated and came out like glass

Any pics of the triumph? 

  • Like 1
On 3/27/2017 at 1:22 PM, pol1on1 said:

Garrett 2860-5 turbos

Trust hard intake pipe kit

HKS dump pipes

HKS front pipe

Hi –Flow cat (Venom)

Tomei Ti Extreme – 3.5” titanium cat back 110mm intercooler.

 

Very flowing now got to save up and do my head port polish n 1mm oversize that would be my dream and cams n lots of stuff thats out of reach haha emoji12.png

 

1mm oversize i doubt would be required unless aiming north of 800hp. bigger ports n valves means more flow but the airspeed slows down and sometimes wont mix as well. bigger isnt always better. i would definetely research more before going down that path. 

 

HeadTorque in Ossie park did port n polish and modified the chambers on mine. they were great to deal with

  • Like 1
On 3/27/2017 at 7:22 PM, pol1on1 said:


I got 19psi on stock internals 412hp just slaps some sticky slicks on and say bye bye to the lumpy v8 that thinks his cool!
Haha

you must have a heap left in it. -5's are good for around 400KW at the wheels IIRC

  • Like 1

so i setup the Water/Meth on my Rodeo before going away Monday, 

 

holy fark it makes some powah now!!! as soon as the pump kicks it, boost jumps up about 4psi and it pulls like a train. Id say it makes 30-40% more powah now. i just hope it doesnt throw a leg outta bed :blink:

  • Like 1
30 will bust it [emoji4]


Pffft

I had more than 42psi and it didn't bust, it just threw raw unburned fuel out the exhaust as it was so rich and timing was so retarded.

It made more than 42 but I don't know how much as that's as far as the map sensor read. Still made 300kw at the wheels while doing it too.
Just now, TiTAN said:

 


Pffft

I had more than 42psi and it didn't bust, it just threw raw unburned fuel out the exhaust as it was so rich and timing was so retarded.

It made more than 42 but I don't know how much as that's as far as the map sensor read. Still made 300kw at the wheels while doing it too.

 

did you go full retard?

  • Like 2

naa, it fluctuates when i move the cable at the pyro. Id say cos the engine rocks lots at idle the cable may have failed. i just fitted a new one and it only lasted 2 days. ill email to see if there is warranty




  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...