Jump to content
SAU Community

Recommended Posts

11 minutes ago, Beyond Blue R33 said:


You love it. I spent all day scanning in a vibro shear manual from 1975 into pdf's then converted into a word document cropped and resized it to a4. 3 hard copies of all manuals for all machinery. 1 on the machienes, 1 in my office and 1 in the big bosses office. Did jha's for all machienery as well. Nice change from welding! We concreted in a totem pole today 1m in the ground for the railway line 3" 2" etc solid bar for hammering lifting pulling and stretching. 8" I beams welded on for strength in the concrete. Nice change:-) loved it!

I walked back into a back log of builds, so had to measure a tank/chassis for a water cart, double check a install on a couple service trucks then start printing cables for the water truck.... so much for a nice relaxed week haha

  • Like 1
I walked back into a back log of builds, so had to measure a tank/chassis for a water cart, double check a install on a couple service trucks then start printing cables for the water truck.... so much for a nice relaxed week haha

What do you for work Macca? Body builder?
4 minutes ago, Beyond Blue R33 said:


What do you for work Macca? Body builder?

 Currently a Auto sparky, ( for how much longer who knows, over it ) we wire up water carts/service trucks/drills etc for the mines but we design/build all the harnesses in perth

Edited by -Macka-
Added info
  • Like 1


It's your turn to come see me,

I always visit you.... you just don't notice me peeking through your window [emoji8]

Trev the peeking duck spying on Italian gourmet kitchens. Sneaking into the car park with a bombed r34. Totally inconspicuous!
1 hour ago, Beyond Blue R33 said:


A nice set of police lights and sirens would be cool? Then I could go on cruises with the big zookey :-/

what...you dont get enough attention in a bright blue sports car that you need flashing lights and sirens haha :cool:

  • Like 1
37 minutes ago, t_revz said:

what...you dont get enough attention in a bright blue sports car that you need flashing lights and sirens haha :cool:

They see the car and then the old dude driving it and asume its his sons......

  • Like 1



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...