Jump to content
SAU Community

R33 Series 2 Bumper On Series 1

GT500_Racer
 Share

Recommended Posts

GT500_Racer Enthusiast

GT500_Racer

Posted
Posted

Hi guys quick question, would the series 2 aftermarket bumper fit fine on the series 1?

Couldn't find a definite answer searching...

Fitment wise, would it still fit or suit the roundness of the s1 lights?

I found a S2 aftermarket bumper bar, since my S1 oem bumper is cracked, an its reasonable priced so figured it might fit but best to ask on here before committing :)

Im not doing a S2 swap, just wanting to know if a S2 bumper will fit S1 with S1 lights and fitment still b fine

cheers

Link to comment
https://www.sau.com.au/forums/topic/456678-r33-series-2-bumper-on-series-1/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

I thought I had a more helpful photo, but the one I have is of the series 2 front with the series 1 bumper that shows the gaps you get there

The REO bar is different between S1 and S2, keep that in mind. The S2 bumper wont fit on the S1 Reo bar.

I can't remember if I even tried to fit my front bumper with the S1 lights still installed but I would just look for a S1 bar or buy a FRP copy from one of the local (Australian) suppliers

Pic attatched in case it helps a little:

image069.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Ok guys thank you very much. GCG highflow it is then 🙂 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...