Jump to content
SAU Community

R32 Dash Mat

gts25

By gts25,
in Exterior & Interior Styling

 Share

Recommended Posts

gts25 Rising Star

gts25

Posted
Posted

Hey Guy's

I am one of the lucky few that has a dash in my R32 GTR with no bubbles/lifting and I want to do as much as possible to keep it that way.

I have had a protectomat dash mat made up by Vechicle Protection Co in CastleHill (www.vipco.com.au)

Very happy with the quality and fit. Its of a very good quality velour and stitch. Other colours are available.

It cost me $85 delivered to regional nsw.

If your interested contact phil at [email protected]. He is very helpful and turned around the mat in a few days. Mention jason from SAU and im sure he will look after you. They should also have mats for the R33/R34

Here are some quick pics. I have yet to fit the velcro/adhesive pads. I reckon it looks great and compliments the interior

post-15055-14330548319016_thumb.jpg

post-15055-14330548798434_thumb.jpg

Cheers

Jase

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/457089-r32-dash-mat/
Share on other sites
gts25 Rising Star

gts25

Posted
  • Author
Posted

Looks great! would be keen on one. wonder if we could get a group buy up

they sure do. i personally dont have the time to organise a group buy but im happy to ask phil if there is a bulk discount.

in my opinion given the quality and fitment they are worth the $70. Thats cheaper then replacing a dash. I doubt there is much margin in such an item to discount but we can ask

Link to comment
https://www.sau.com.au/forums/topic/457089-r32-dash-mat/#findComment-7543351
Share on other sites
gts25 Rising Star

gts25

Posted
  • Author
Posted

What holds it up/on ?

Seen the damage the Velcro tabs (glue) can do from dash pads. Hence my question.

That one seems to fit better than some I have seen

At the moment nothing. It is so well fitted to the design of the dash it needs nothing to hold it.

I have also done a drive up macquarie pass last week and the mat didnt budge

an adhesive velcro stripped is supplied and i will fit in places where the mat sits up a little.

Before purchasing I did enquire about what damage the adhesive can do. Phil confirmed it cleans up easy with Metho

Jase

Link to comment
https://www.sau.com.au/forums/topic/457089-r32-dash-mat/#findComment-7543352
Share on other sites
  • 1 month later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
×
×
  • Create New...