Jump to content
SAU Community

Steering Wheel Series 1 To Series 2 Nissan Skyline R33

Rado33

By Rado33,
in General Maintenance

 Share

Recommended Posts

Rado33 Rookie

Rado33

Posted
Posted

Hey guys I got a Series 2 steering wheel fitted into my R33 and I was wondering is there anyway possible I could make the horn work? I've got a Series 2 motor with a Series 1 body. If anyone can help me would be much appreciated. Also I like to mention that I changed the Relay and 10 Red fuse and still no luck. If anyone is out there to help me I'd be more then thankful for your help. If someone could possibly help me out that has been through a similar situation and meets my requirements would be thankful for the help.

I'm open to any opinion but don't quote anything stupid because I won't tolerate any rude behaviour.

  • Like 1
89CAL Grand Master

89CAL

Posted
Posted

Your horn doesnt work after youve changed steering wheels? Sounds like something wasnt plugged in properly when the wheel was put on. The s2 wheels have air bags (all of them AFAIK, maybe the GTS' dont?) So are you sure you havent hooked something up wrong?

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

S1 (with airbag) vs S2 with airbag is very different.

S1 has the SRS module built into the wheel where as most (not all) S2 has the SRS module under the centre console.

If you want a S2 wheel, perhaps get a 180SX Type-X wheel as it uses the same setup as the older S1 with airbag.

  • 1 month later...
Rado33 Rookie

Rado33

Posted
  • Author
Posted

Should only be a ground wire. I've done s2 stag to a s1. So tech it's 34 to 33.

Hey bro how did you get that to work? Because my mate gave me his Steering wheel out of his 180sx and I put it in mine and theres still no luck to get it to work. If u can help it would be much appreciated.

Rado33 Rookie

Rado33

Posted
  • Author
Posted
S1 (with airbag) vs S2 with airbag is very different.

S1 has the SRS module built into the wheel where as most (not all) S2 has the SRS module under the centre console.

If you want a S2 wheel, perhaps get a 180SX Type-X wheel as it uses the same setup as the older S1 with airbag.[/quote

I've got one steering wheel from my mates 180sx but theres still no luck getting the horn to work

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
×
×
  • Create New...