Jump to content
SAU Community

Recommended Posts

When i had TS0.82 on a 6boost, felt same as an open 0.82 on stock mani, but i lost 500rpms response for some reason, was same tune and everything else identical.. single gate on the housing but further around the snail so maybe that caused it? E85

Stock mani, gate off housing was best setup...

longer runners will induce some lag but not as much as 500 rpm.

another way around it is to come on boost a little leaner with less timing. This will increase EGTs and get the turbo to boogie quicker

I'm tempted to FSU and go a GTX, twin scroll with twin gates if I ever get bored.

  • Like 1

longer runners will induce some lag but not as much as 500 rpm.

another way around it is to come on boost a little leaner with less timing. This will increase EGTs and get the turbo to boogie quicker

I'm tempted to FSU and go a GTX, twin scroll with twin gates if I ever get bored.

Yeah, i was expecting full boost of 20psi at 3500rpm, the GTX on stock mani did 20psi at 3800rpm with exact same tune etc...

This short clip you can see nothing happens till almost 5000rpm so it was not like a 0.63open at all..

^ that is laggy, however is your rpm gauge reading correctly?

I know mine has about a 200rpm difference to what is being shown by the ECU up the top end.

Never know, your cluster could be off its tits

post-93368-14380721219504_thumb.jpg

Here is mine, .82(I think, maybe .78) twinscroll on 6boost manifold.

From memory Trent was saying the rear housing was holding it back from making more top end. The graphs are 98 and e85.

I'd be interested in seeing what a 1.01/1.06 rear would do, I've been thinking of doing the swap

  • Like 1

Yeah, i was expecting full boost of 20psi at 3500rpm, the GTX on stock mani did 20psi at 3800rpm with exact same tune etc...

This short clip you can see nothing happens till almost 5000rpm so it was not like a 0.63open at all..

https://youtu.be/2ZjV5Pb5ySc

Lag for days !

attachicon.gifImageUploadedBySAU Community1438072122.747273.jpg

Here is mine, .82(I think, maybe .78) twinscroll on 6boost manifold.

From memory Trent was saying the rear housing was holding it back from making more top end. The graphs are 98 and e85.

I'd be interested in seeing what a 1.01/1.06 rear would do, I've been thinking of doing the swap

Not a bad result! The e85 makes such a big difference.. yeh i honestly havent seen any set ups twin scroll, gtx3076 with 1.06a/r am interested to see how itd go...

U got 289 kw on 98...i woulda expected a little more ? At least 300? Judging by others results...what boost was that at?

Edited by Kmac92

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
×
×
  • Create New...