Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm currently in the build with a R32 GTR. I'm looking to maximize tyre width within the factory guards. I'm aware 18x10.5+22 is near on optimum.

Has anyone had any success with an 18x11 square setup? +30 offset is available and should fit reasonably flush, however I'm unsure how much inner guard/suspension clearance is available.

Anyone able to provide some feedback on this?

thanks in advance.

Jme

Link to comment
https://www.sau.com.au/forums/topic/458631-r32-gtr-18x11-question/
Share on other sites

People have enough issues getting 275s/285s on a 10" rim without guard modifications (and assuming it's not silly low), and still grabbing the inner guard (even on 265s, depending on offset)

You're aiming to get a tyre wider than 275s on there with 11"?

So not sure how a 11" and 295/305 is really going to work with factory guards.

I would not attempt 11 inches wide that 18x10.5 +22 will need some decent camber tho, I have 18x10 +18 with bout 1.5deg camber clears inner plastic by about 4 to 5mm on full lock no problem with 265 35 ku39s so i cant see how you can fit any wider and not hit things unless you remove inner plastics then that's a different story.

my guard plastics still in also just used a heat gun to reshape lips so no cutting was done looks smick as.

Edited by mr skidz

275 is too stretchy for me, will go to 285 next round of tyre changes.

Your +20s with 275s should have the same gap to the upright as my +25s with 265s. Do you have more than 5mm gap? (And how much do tyres flex laterally on hard cornering?)

yeah your od would be a wee bit bigger with a 275 plus your 20 offset is 2 Mill further out than mine which doesn't help either on that corner angle. it's a combination of 2 mill extra offset and overall tyres diameter that hits that plastic liner.

My suspension is completely stock standard so no caster rod adjustment but if you were to adjust your castor you could bring your front wheel back if you wanted to but I would prefer it more forward that's just me

Edited by mr skidz

I have about 5-5.5deg caster. Agree, if I went a more 'rounded' tyre (have Hankook R-S3 at the moment) and raised the front a bit, it'll be fine.

Track-ready-BNR34.jpg

Source: http://run-it-hard.com/2015/06/skylines-australia-nsw-june-monthly-meet/

Rolling shot!

19326387095_40537b0b97_b.jpg

Source:http://www.sau.com.au/forums/topic/457435-sau-nsw-june-monthly-meet-mac-pass-charity-cruise/page-12#entry7560676

Used to sit like this hahaha:

10955734_10152962562296259_2560210221909

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...