Jump to content
SAU Community

Recommended Posts

I've searched high and low for this but only come up with a few confused posts that may or may not be accurate.

I'm looking for the dimensions for PNM35 ARX wheels, and if they're the same as NM35 ARX wheels?

My car is in transit and has aftermarket wheels that I would like to return to factory Nissan wheels before compliance so I want to get something that is the same as what came on the car, if not the originals.

Cheers,

Nick

Link to comment
https://www.sau.com.au/forums/topic/458813-arx-wheel-dimensions/
Share on other sites

While on the topic of wheel dimensions, does anyone have the dimensions for 350RX 18s and whether they're the same size as the V35 premium 18s? My V35 premium wheels were staggered 7.5/8.5 but I believe some were 7.5 all round? I remember they used to look like roller skates compared to mine.

Same as the ones pictured.

2005-Nissan-Stagea-350RX_01.jpg

4337_1099031330244_2436466_n.jpg?oh=d3c4

While on the topic of wheel dimensions, does anyone have the dimensions for 350RX 18s and whether they're the same size as the V35 premium 18s? My V35 premium wheels were staggered 7.5/8.5 but I believe some were 7.5 all round? I remember they used to look like roller skates compared to mine.

Same as the ones pictured.

2005-Nissan-Stagea-350RX_01.jpg

4337_1099031330244_2436466_n.jpg?oh=d3c4

The v35 premium wheels are 8" all round not 7.5

Cool, makes sense. I'm going out on a limb and guessing the later model ARX wheels are also 7.5, they look identical.

The problem I have is my car is arriving without factory wheels that will be too wide for compliance. I like the 350rx wheels but if the offset needs to be wider for the ARX to fit neatly then 350rx wheels will look pox.

I had a set of Nissan GT coupe sport edition wheels on my C34 (picture attached - caption says M35 wheels but they are not) They were 18 x 8 +30 all round

I currently have in my possession a set of wheels allegedly off a V36 Skyline GT which are 17 x 7.5 +40 all round.

post-49463-0-17434700-1439154225_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...