Jump to content
SAU Community

Recommended Posts

Dont know if anyone has thought of this or has actually carried out this modification.

Want my tuner recommends is that i put a low fuel level switch in my surge tank in case the lift pump decides to kick the bucket.

The sensor would be tapped in about half way up the tank and would be wired into a light on the dash to indicate if fuel was starting to get low and therefore potentially saving an engine. Yes i understand that i can get a Air/fuel gauge or a low fuel pressure light but thats more for the pumps inside the tank that feed the rail.

Does this seem like a reasonable idea and if not why?

Also trying to figure out what sensor to use? would a low coolant sensor register petrol and/or E85?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/458932-surge-tank-low-fuel-level-switch/
Share on other sites

Hmm I was going to suggest a mercury tilt switch but it would require some room in the surge tank. What about a flow meter on the line from the lift pump to the surge tank? Or a pressure switch (similar to an oil pressure warning light or maybe even an actual oil pressure warning light) installed in a T off the feed line.

my memory may be a bit fuzzy but doesnt that switch kick in when the float sinks too low?

I need something i can tap into the side of the tank as inside the tank is already full of pumps :D

It's a seperate thing. I think it's what you want.

Google "low fuel annunciator", its the same thing as used on aircraft.

Also been looking into it for my surge tank setup.

My way of thinking was to wire it into the Haltec as a engine safe guard, should react faster than you pulling off the throttle, that is if you see the light of course.....

Many factory fuel pump cradles have a separate low fuel sensor fitted, i have not had time to work out which one id be using yet.

Edited by GTRPSI

Hmm I was going to suggest a mercury tilt switch but it would require some room in the surge tank. What about a flow meter on the line from the lift pump to the surge tank? Or a pressure switch (similar to an oil pressure warning light or maybe even an actual oil pressure warning light) installed in a T off the feed line.

The flow meter would work well, not sure how the pressure switch would work as the pump isn't really producing much/ if any pressure as far as I can tell.

Ben I'm trying to imagine how it would all work in terms of wiring and mounting up the sensor. The unit is obviously sealed so everything that runs in and out of the tank needs to be easily sealed back up to prevent leaks.

Here's the tank to give you an idea of what I'm dealing with

post-47556-0-43767900-1439289951_thumb.jpgpost-47556-0-51087300-1439289970_thumb.jpg

Look at the 2 links below...

http://www.aeu86.org/forum/showthread.php?pid=151308

https://www.google.com.au/search?q=low+fuel+light+thermistor&biw=1920&bih=920&tbm=isch&tbo=u&source=univ&sa=X&ved=0CCQQsARqFQoTCMC-1_vsoMcCFYfNgAodMoEMUQ

You would simply need to mount it with a hose clamp to the height you want it at, somewhere along the cradle shaft into the surge tank on on a pump if its in there.

Hey guys, thanks for the replies

Ill have to ask the tuner about an engine cut off, ill probably just position it somewhere in my eye line to keep things simple.

I've managed to get a 3 pin digital sensor that is used on generator fuel tanks. Once I hook it all up ill report back

Its easy to organise an engine cut off but you are better off without it as depending on how far up (or down) the catch can you put the sensor you should easily have enough fuel to get back to the pits rather than get stranded out on the track.

Hmm I was going to suggest a mercury tilt switch but it would require some room in the surge tank. What about a flow meter on the line from the lift pump to the surge tank? Or a pressure switch (similar to an oil pressure warning light or maybe even an actual oil pressure warning light) installed in a T off the feed line.

You forgot a simple flow switch.

Thats what id be using on the line into the tank.

Joey, If you're worried every time your ~5l tank uses 2.5l you might as well have a 3l tank.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...