Jump to content
SAU Community

Recommended Posts

Dont know if anyone has thought of this or has actually carried out this modification.

Want my tuner recommends is that i put a low fuel level switch in my surge tank in case the lift pump decides to kick the bucket.

The sensor would be tapped in about half way up the tank and would be wired into a light on the dash to indicate if fuel was starting to get low and therefore potentially saving an engine. Yes i understand that i can get a Air/fuel gauge or a low fuel pressure light but thats more for the pumps inside the tank that feed the rail.

Does this seem like a reasonable idea and if not why?

Also trying to figure out what sensor to use? would a low coolant sensor register petrol and/or E85?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/458932-surge-tank-low-fuel-level-switch/
Share on other sites

Hmm I was going to suggest a mercury tilt switch but it would require some room in the surge tank. What about a flow meter on the line from the lift pump to the surge tank? Or a pressure switch (similar to an oil pressure warning light or maybe even an actual oil pressure warning light) installed in a T off the feed line.

my memory may be a bit fuzzy but doesnt that switch kick in when the float sinks too low?

I need something i can tap into the side of the tank as inside the tank is already full of pumps :D

It's a seperate thing. I think it's what you want.

Google "low fuel annunciator", its the same thing as used on aircraft.

Also been looking into it for my surge tank setup.

My way of thinking was to wire it into the Haltec as a engine safe guard, should react faster than you pulling off the throttle, that is if you see the light of course.....

Many factory fuel pump cradles have a separate low fuel sensor fitted, i have not had time to work out which one id be using yet.

Edited by GTRPSI

Hmm I was going to suggest a mercury tilt switch but it would require some room in the surge tank. What about a flow meter on the line from the lift pump to the surge tank? Or a pressure switch (similar to an oil pressure warning light or maybe even an actual oil pressure warning light) installed in a T off the feed line.

The flow meter would work well, not sure how the pressure switch would work as the pump isn't really producing much/ if any pressure as far as I can tell.

Ben I'm trying to imagine how it would all work in terms of wiring and mounting up the sensor. The unit is obviously sealed so everything that runs in and out of the tank needs to be easily sealed back up to prevent leaks.

Here's the tank to give you an idea of what I'm dealing with

post-47556-0-43767900-1439289951_thumb.jpgpost-47556-0-51087300-1439289970_thumb.jpg

Look at the 2 links below...

http://www.aeu86.org/forum/showthread.php?pid=151308

https://www.google.com.au/search?q=low+fuel+light+thermistor&biw=1920&bih=920&tbm=isch&tbo=u&source=univ&sa=X&ved=0CCQQsARqFQoTCMC-1_vsoMcCFYfNgAodMoEMUQ

You would simply need to mount it with a hose clamp to the height you want it at, somewhere along the cradle shaft into the surge tank on on a pump if its in there.

Hey guys, thanks for the replies

Ill have to ask the tuner about an engine cut off, ill probably just position it somewhere in my eye line to keep things simple.

I've managed to get a 3 pin digital sensor that is used on generator fuel tanks. Once I hook it all up ill report back

Its easy to organise an engine cut off but you are better off without it as depending on how far up (or down) the catch can you put the sensor you should easily have enough fuel to get back to the pits rather than get stranded out on the track.

Hmm I was going to suggest a mercury tilt switch but it would require some room in the surge tank. What about a flow meter on the line from the lift pump to the surge tank? Or a pressure switch (similar to an oil pressure warning light or maybe even an actual oil pressure warning light) installed in a T off the feed line.

You forgot a simple flow switch.

Thats what id be using on the line into the tank.

Joey, If you're worried every time your ~5l tank uses 2.5l you might as well have a 3l tank.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...