Jump to content
SAU Community

XTC Drift Day @ Morwell - Invite to SAU

Dr_Drift

By Dr_Drift,
in Archived Events

 Share

Recommended Posts

Dr_Drift Veteran

Dr_Drift

Posted
Posted

I've organised a drift day with NS.com and thought a few SAU members may be interested in attending. For the first drift day we will be having publicity and request intermediate or advance drifters for the first event, and subsequent events will be open to all..... If this first one goes well I'll organise an SAU drift day in the very near future...

XTC & NS.COM Morewell Drift Day

The details have been finalised.

WHERE: Morewell Hill Climb Circuit

WHEN: 21st August 2004, 9:00 am till 6:00 pm

COST: $75 Track Fee, $25 Annual Membership

Morwell is located about two hours out of Melbourne. The event will recieve full coverage in magazine (most likely Drift Battle), and probably TV also. The track will be available for the whole day with ambulance and marshals present for safety. Numbers will be strictly limited to ensure maximum track time. Gold Coin Donation entry for all spectators. All profits will be donated to the Track.

There will be a drivers briefing at 10am and is ESSENTIAL for all drivers, if you miss it you don't drive.

Remeber:

1. Two hours drive down and back

2. Can transport all their own spare rims and tires (no fitting available)

3. $50 Deposit required to confirm place

4. Can drift reasonably well as the first event will be getting massive exposure

Please e-mail, call me on 0425 818 755, or drop in at XTC to arrange payments.

Doc.

Link to comment
https://www.sau.com.au/forums/topic/45921-xtc-drift-day-morwell-invite-to-sau/
Share on other sites
  • 2 weeks later...
inark Grand Master

inark

Posted
Posted

is it really essential to be half decent? :( i wouldnt mind bring the ceffy as i should have it on the rd by then... but if ur going to hold another one when would it be? i'll go along to a couple of calder prac events before the next one :)

Dr_Drift Veteran

Dr_Drift

Posted
  • Author
Posted
"if it gets there??" thought the innards were fine man, did you find somthing in there?

Nah, getting some headwork done, and also ordered my flared guards to fit my 17x8's all round :)

  • 4 weeks later...
Dr_Drift Veteran

Dr_Drift

Posted
  • Author
Posted

I must confess I did scratch one of those horrid Zelda Tri Spoke when I had it, but never did infact bent it at all ...

.... sniffs.... i miss that car when it was straight :D

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...