Jump to content
SAU Community

Recommended Posts

Hi I'm new to this forum had my car for about 2and a half years so have got to know my car well just a quick question I usually service my car with motul 300v chrono 10W 40 every 5000kms but while I was down south I needed to top up oil and the best I could get was penrite hpr 15w 40 semi synthetic would've used no more than about 800 ml and I'm just really worried if I done any damage to it drove about 300km since top up am I better off not driving it till I do an oil change as it seems a bit different when driving. Cars a r33Gtr with mild mods sorry if question has been asked before couldn't find a specific answer relating to my concerns. Any advice will be greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/459215-oil-issue/
Share on other sites

Ryco are fine, you need a new mechanic mate. The only thing the greddy filter gives you is a big hit to the wallet that you don't need.

I bet if you opened them up internally they would be very similar if not the same type of filter material and design.

The comparison has been done between an OEM and Ryco filter and the difference between the two was not much.

Link to comment
https://www.sau.com.au/forums/topic/459215-oil-issue/#findComment-7594249
Share on other sites

Mate I think you need to apply your own thoughts instead of taking what your mechanic says as gospel.

At any oil change, do you really think every last cc of oil comes out that sump plug?

Of course not, there's always going to be dilution of your new oil with old oil remaining in galleries and various pockets.

Now if you noticed some dramatic change in your car's road performance after you topped up with 800cc of different viscosity oil, I'd be more concerned how come it needed topping up at all.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/459215-oil-issue/#findComment-7594269
Share on other sites

I know not every drop comes out at oil changes I'm definitely looking for a new workshop, I thought it could be losing oil somewhere cause usually when I service I don't require any top up. As for dramatically losing performance just was told oil was to thick to flow properly but I now think that's not the case and I doubt it needs a new dyno tune after a few months. As for the filter I done some research and it's definitely not worth the extra cash so going to be using ryco filters from now on.

Link to comment
https://www.sau.com.au/forums/topic/459215-oil-issue/#findComment-7594301
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...