Jump to content
SAU Community

Stock R34 Gtt Brakes, New Gtr Brake Rotors, Rays Wheels, Ces Dump/front Pipe

DekA
 Share

Recommended Posts

DekA Experienced

DekA

Posted
Posted

Selling some leftover parts from some recent upgrades.

  • Stock R34 GTT brake callipers and DBA 4000 T3 rotors. Inside piston on front passenger calliper was sticking resulting in the one very worn rotor. Near new QFM HPX pads. - $400
  • New R32/R33/R34 Brembo DBA 4000 T3 brake rotors. Had to get different rotors when I found out the callipers I was sold were V35 rather than GTR. Never used, still in boxes. - $650 SOLD
  • Staggered set of Rays Volk GT-P wheels 18x8.5 and 18x9.5. Unsure on specific offset but had to run a 10mm spacer on the front to clear stock brakes. 80% KU31 tyres on rears, front KU36 tyres need replacing. - $750
  • CES split dump front pipe with flex section and extra port for wideband O2 sensor. - $300
  • HID headlight kit. New, never used and still in original packaging. - $100
  • Mishimoto Universal Transmission / Power Steering Cooler Kit. New, never used and still in original packaging. - $150
  • R34 GTT stock OP6 turbo. Used, was working fine when replaced. - $150 SOLD

Willing to post the HID and trans cooler kits at buyers expense. Rest of the parts are pickup-only. Location Sydney.

Pics:

post-91912-0-84176300-1440829403_thumb.jpg
post-91912-0-01571300-1440829447_thumb.jpg
post-91912-0-51812200-1440829487_thumb.jpg
post-91912-0-37386100-1440829517_thumb.jpg
post-91912-0-91791400-1440829545_thumb.jpg
post-91912-0-64567400-1440829570_thumb.jpg
post-91912-0-81392300-1440829596_thumb.jpg
post-91912-0-59597600-1440829624_thumb.jpg
post-91912-0-48391600-1440829652_thumb.jpg
post-91912-0-19532500-1440829683_thumb.jpg

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...