Jump to content
SAU Community

Valve Body Programming

tomo123

By tomo123,
in Four Door Family & Wagoneers

 Share

Recommended Posts

tomo123 Collaborator

tomo123

Posted
  • Author
Posted

What was the name of the trans specialist down here?

Are you sure it needs reprogramming? They would normally read the data off the old ecu and swap it back on to the new one once the valve body was replaced, using the Consult3, via the OBD2 connector.

Transmission specialist here is Mick Taylor, my car was sitting there for 2 months before I decided this is ridiculous.

When I call back the nissan dealer ill tell them they should be able to do it in house, every company i call asks for my VIN though. As soon as they find out its JDM they can't do anything.

Supposedly some computers have to be changed Leroy

Equilibrise Community Regular

Equilibrise

Posted
Posted

I posted up directions on sau for how to put tranny ecu in diagnostics mode to get fault codes and clear/ reset them. Might be worth checking out yourself and clearing them. I had a similar problem with mine and after clearing the codes the problem disappeared. I hope you will have the same outcome. Good luck either way.

iamhe77 Grand Master

iamhe77

Posted
Posted (edited)

Transmission specialist here is Mick Taylor, my car was sitting there for 2 months before I decided this is ridiculous.

When I call back the nissan dealer ill tell them they should be able to do it in house, every company i call asks for my VIN though. As soon as they find out its JDM they can't do anything.

Supposedly some computers have to be changed Leroy

Most (all?) Nissan dealerships will have a local version of FAST and an import version of FAST.

They may be referencing this when they say "have to change computer", meaning that they have to physically get up and move to the computer that has the import version of FAST on it.

This may be seen as too much effort for some.

EDIT: Yes, I understand how salty I am. Sue me.

Edited by iamhe77
scotty nm35 Grand Master

scotty nm35

Posted
Posted

It's all done on the Consult3 Toughbook, no need to move desktop computers Cam. :P

Yes there is only one program, and they need to change the software to JDM but a good diagnostic tech can do that easily.

  • 2 weeks later...
tomo123 Collaborator

tomo123

Posted
  • Author
Posted

Found out the valve body itself doesn't need any programming, it's the mechatronic unit attached to the valve body that needs to be programmed. Currently the mission is finding a new valve body and mechatronic assembly.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...