Jump to content
SAU Community

Recommended Posts

Finally got specs on the short motor. No receipts for the parts but the pistons are stamped with spool logos.

The motor is prepped for a 26 head. the head stud holes are tapped out to fit oversized rb26 studs. New ARP head studs and cometic metal gasket to suit - an RB26 head will bolt straight on. ARP RB30 main studs have been used on the bottom end.
Main bearings are .25mm over
Big End bearings are .25mm over
Bore is 86.5mm – (0.5mm over)
compression ratio is 9:1
All bearings are ACL race bearings.

Have confirmed I'll go see him on Wednesday the 23rd, he has one other buyer from interstate trying to get up tpo see him and wouldn't accept a refundable holding deposit but said he would tell me if the other guy was going to get there before me - though he thought that unlikely.

I asked what sort of non refundable deposit he wanted if it came to that and he said just enough to cover doing another roadworthy if I didn't buy, couple hundred at most, so if the other guy gets there before me I'll just put that money down to give me a chance to inspect and first dibs on buying.

Car is in at Godzilla today.

I'm willing to risk a couple hundred to buy me time to get there.

He did say I was far and away the most engaged and knowledgeable buyer, the type of person he was hoping would buy (as the car is his baby etc).

He was fairly confident I would be inspecting first, but said he'd keep me posted.

I'm still trying to wrangle the inclusion of the PowerFC also as I have a mate who wants it :)

Some interesting/bad news.

Car went in for check over and tune - with the bigger exhaust on.

At 18psi, it only maid a bit over 300awkw, which seems low for -5s on 18psi. On 21psi, it made around 335awkw, which to me still seemed low based on RB26 dyno thread figures. Maybe those numbers are RWKW though? Anyone kow what the AW to RW loss is? I didn't think it was very much,

Also, compression test showed this.

150

155

160

135

165

155

That was a cold test. He is going to get it checked elsewhere cold and hot but 135 seems suspect to me, it's also greater than the 14 or so PSI the service manual allows.

I'm interested to see what a second test shows up.

Thoughts?

Spoke to Chris at Race Pace to pick his brain.

Got some pricing on rebuilds etc for reference.

Interestingly, he felt that the PFC was the better ECU for that car, but did admit the Haltech has a lot more features.

As per the above see what the second test shows up.

There's not enough $$ to come from spares to cover the cost of a rebuild at Race PAce, I do have some other options but just wanted to start with those guys.

He's just called me, gone and bought a new gauge and done his own test and claimed that cyl 4 came up as 160.

I questioned if that was warm or cold and he mentioned the car is likely still warm from being in the shop earlier and will do another test tomorrow morning dead cold.

That might explain why it's down on power.

I am so bummed right now I cannot even begin to explain it.

but they wont be able to handle the boost that the bigger -5's can.

I remember this topic being brought up once before, I think it came down to the volume of air that is being smashed into the motor is not much different between the 2. whereas with more boost the -5's leave -7s/-9's for dead

My 32 with -5's made 287kW rears on 18psi stock motor. So not interested in running more than 18 nor 300 club. I'd rather the non-blown engine club.

Seems pretty ok imo.

Made about 246 kW on 14psi as well, cant remember if I had changed anything from the 14 to the 18psi runs.

Edited by okooko

I've always thought you did both and should expect the same type of variance across all cylinders.

If one is down when cold then up when warm, that's a ring sealing issue - which could be rings or bores, but simply rules out valves.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...