Jump to content
SAU Community

Recommended Posts

Hello all,

I have a 1995 R33 GTR and I recently completed an LS2 coil swap on the car. It ran great until recently, when I started noticing a slight shudder and rougher idle. Thought it was a MAF issue so I cleaned them up, and resoldered them.

I also decided to clean up the plugs and to my surprise, found that plug no. 5 was completely black, and oily. Now I dont know if this is a sign of a blown cylinder or low compression, but I decided to swap out coil no. 5 and changed the coil wire, but no change.

I am at my wit's end, trying to figure out what is wrong with that cylinder and would really appreciate if someone could shed some light on what to do here. I live in a remote town in Canada, and do not have access to most things people do in larger towns, so have to depend on myself to carry out any tests or check things. This has gotten worse over the last 2-3 days, as I drove the car on a 200 mile trip, which was great until I got back home and it started to show signs of running stupid rich while cruising and lean when boosting.

I have checked the coils, the wires and the plugs are all good. When I disconnect the coil wires no. 5, there is a very very minor change in the revs if at all. I can hear the coil ticking and the spark is there. If the injector wasnt firing, would it foul up the plug with black oily stuff?

How do I check without the car running if the spark is strong enough? Could it be faulty injector or a weak spark? Is it also possible that cylinder 5 has lost compression?

Please help me :(

Thank you.

Possible that the injectors is buggered and pissing too much fuel in. Also possible that it's buggered, not put enough fuel in, you have run that cylinder lean and it is now rooted. Also possible that the rings on that cylinder have just died on their own.

Injectors out and flow tested are probably the on only way to tell if either of the 1st 2 are true.

Could be a injector doing that for sure. Stuck open or not right. Has the car ever been run on Ethanol gas?

Ive had this exact same issue with ethanol many a few times. I Learned Stock R33 injectors just seem to die on ethanol within a few months, no idea exactly why.

Edited by sonicz

Could be a injector doing that for sure. Stuck open or not right. Has the car ever been run on Ethanol gas?

Ive had this exact same issue with ethanol many a few times. I Learned Stock R33 injectors just seem to die on ethanol within a few months, no idea exactly why.

odd never had an issue in 7 years... unless they were highflowed std items then yes nearly every set of ive had through have failed.

odd never had an issue in 7 years... unless they were highflowed std items then yes nearly every set of ive had through have failed.

Nope, I've had 2 completely stock sets die, each set lasting about 2-3 months of E85 use. The original + a stock used set, all died a slow one by one death.

I think I read something about the Series 1 constantly sending 12 power to the injector loom even when the car is off, which i turn causes corrosion of the internals of the injector, but was later changed not to do this in later series, maybe series 2?. If anyone can confirm or deny would be great.

I have a set that were on their way out to the point the car barely ran, i.e at least 3 of them will be dead. If you have the means to found out what is wrong with them I can send the entire set of 6 you free of charge, bar the cost of postage. Maybe we can split that as I very curious to know what the cause of death is. I never bothered to find out.

Nope, I've had 2 completely stock sets die, each set lasting about 2-3 months of E85 use. The original + a stock used set, all died a slow one by one death.

I think I read something about the Series 1 constantly sending 12 power to the injector loom even when the car is off, which i turn causes corrosion of the internals of the injector, but was later changed not to do this in later series, maybe series 2?. If anyone can confirm or deny would be great.

I have a set that were on their way out to the point the car barely ran, i.e at least 3 of them will be dead. If you have the means to found out what is wrong with them I can send the entire set of 6 you free of charge, bar the cost of postage. Maybe we can split that as I very curious to know what the cause of death is. I never bothered to find out.

Were you offering this to me or to STATUS?

Secondly, on the issue itself, if the cylinder was toast, wouldnt I smell fuel on the plug no.5? All I see on the plug itself is that it coated with black oily stuff and its not like it is covered in oil...just a complete oily blackness.

If the cylinder was toast, would the car still rev high? The AFRs are erratic, but lean out under boost/WOT. I dont have a compression tester, but assuming the compression is zero, what symptom(s) would the car have? There is only a slight drop in performance under load. It does spit black soot out of the exhaust upon cold start, mixed with water. But there is no blue or black smoke coming out.

Just checked compression. 70 psi in cylinder 5.

I drove the car to a shop and it drove fine, even with this low compression. Injector was firing, and so were the coils. Seems either the bottom end is fried or the top end is messed up - could be a partially stuck valve/lifter/ faulty spring, or do you guys think it is the bottom-end?

This is devastating. I dont know what to do....

Sounds like the head gasket is shot.

Worst case, you may have had a piston ring land fail.

Head off, investigate further.

Annoying, yes. Devastating, not really.

It's probably seen some service, and presume you're happy to give it some stick?

The mechanic who did the compression test says that it is unlikely anything within the bottom-end, although I have my doubts. It could be the rings or ring land, but I am not an expert to comment.

There is no oil-coolant mixing in the radiator or the oil pan. The car doesnt smoke black, blue or white. The AFRs on my wideband are kinda spot on when itdling, but are erratic and go up and down quite a bit, and running leaner under WOT. The plug for cylinder 5 was covered in oil/petrol mix, totally black and oily. He thinks it is the head/valve/springs, etc..

The car still pulls strong even with this issue, and boosted fine. Just that I can see the rear turbo doesnt spool as well as the front, possibly due to loss of exhaust pressure from cylinder 5 coming in, which makes me think that perhaps the exhaust valve is burnt or messed up?

He says that there is no need to do a leakdown test as we cant really ensure the cylinder 5 chamber would be completely sealed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...