Jump to content
SAU Community

Recommended Posts

Hey Team,

I'm trying to eek out the most from my set of Hankook soft 221's. I'm hoping to get one more trackday out of them....

They have done 3 track days... 2 of them wet. (in the last 9 months or so)

I have another coming up on the 17th Dec at the my usual track, Wakefield.

Now the question is what would you run on the front and back? As you can see they are marked for RF LF RR LR.

The Rears are very low and the fronts have started to melt.

Should I keep running the fronts where is, to make the most of the grip for turning or put them on the back and get drive?

Seems obvious that I put the ones with the most tread on the back, but Wakefield is such a tight turning track.

They are on an R33 GTR.

Thoughts?

20151119_150342_zpsgp8aeq27.jpg

20151119_150348_zpshaggayrs.jpg

20151119_150352_zpsrlbzckdo.jpg

20151119_150404_zpsdqq0zwr1.jpg

Link to comment
https://www.sau.com.au/forums/topic/461149-semi-slicks-what-would-you-do/
Share on other sites

haha I think the opposite....if you take softs to a track day at wakefield in December you will destroy them. probably in the first session. so it doesn't matter which one goes on which corner :P

keep those for hillclimbs or super sprints, and go and buy a set of medium or hard tyres instead.

  • Like 1

Hankook Z221 softs (C70) are like Yokohama A050 Mediums. Maybe a fraction softer, but not alot.

I've done a hillclimb, 2 Lakeside days (1 over 30 degrees ambient), 2 days at Morgan Park in 33 degree heat and 1 day at Phillip Island on a 1530kg Soarer. Tyres are about half worn except for the outer edges. I was planning on flipping them on the wheels to maximise their life, but I think the rear tyres may have gone off now - I had no rear grip at the last track day and it got worse with each lap... I should have changed them front to back to see if the problem moved with the tyres, but CBF. It was too hot

A couple of mates who run Hankooks have had the same thing happen - they go off before they wear out.

Edited by hrd-hr30

Good to hear, I haven't used them myself, I was just going off my experience with other soft tyres

In that case, bang them on any corner, have fun until lunch, then check them for rotation for the afternoon. I'd always put the best tyres on the most loaded point which is front left at wakie....you can always control the amount of rear wheel work with your foot....

  • Like 1

yeah, but if you don't know what they're like brand new, you can't really say they're consistent down to the belts. Mine ran effortless 59s brand new. Now at about 50%, 1:01.2 was all I could do. Might be why that bloke was selling his... They're still faster than Nittos, but nothing like what they were new.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...