Jump to content
SAU Community

Recommended Posts

Hey guys

Sold my car and have some parts that never got a chance of using and some OEM used ones, basically a garage clean out will keep adding as i find more stuff.

1) Brand New in unopened box CST Type Vettel V36 coilovers fully adjustable with 14k front and 9k rear spring rates and 16 way damper. These are made in Japan and distributed by Tanabe. $1500 ono (pic of suspension out of box from google, i havent opened my box yet)

2) Blitz Power-sus intake panel filters also BNIB $120

3) V36 Type S and SP front lip kit ( Fibreglass sides with CF middle part, see pics) $550 ONO

4) RS-S LowDown springs BNIB $400

5) OEM Used Exhaust axle back Muffler and y-pipe $100

6) OEM Used Manifold $100 (good for anyone needing to send one into z1motorsports as core unit)

7) OEM Used rear chrome bootlip $50

8) OEM Used 18" V36 Coupe wheels made by enkei in excellent condition need tires $500

9) OEM Used 18" V36 Sedan Type SP wheels also in excellent condition (front tires good, rears need replacing) $500

10) BNIB plug and play V36 cruise control kit (comes with a little wheel knob that can be used to set/cancel and increase/decrease speed see pics) $500 ONO

Thats all from the top of my head, like i said if i find more stuff ill keep adding.

Offers only accepted if i have put an ONO next to the price or else its non-negotiable.

PM will be the best way for enquiries and everything located Southwest of Brisbane

post-23808-0-04906100-1448160855_thumb.jpg

post-23808-0-53757800-1448160857_thumb.jpg

post-23808-0-12327600-1448160858_thumb.jpg

post-23808-0-06436200-1448160878_thumb.jpg

post-23808-0-63433400-1448161012_thumb.gif

Link to comment
https://www.sau.com.au/forums/topic/461196-v36-parts-for-sale-garage-cleanout/
Share on other sites

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

It works both as a cruise and throttle controller, install is simple plug and play as it is V36 specific and will fit into factory accelerator harness and a few wires need to be hard wires like power and brake pedal. Check the attached wiring diagram.

post-23808-0-09654300-1448288062_thumb.jpg

VQ35HR and VQ37VHR Carbonfibre intakes used for about 1000-1500kms only.

$350

Was there a reason you removed it after a short time ? Did you notice any performance increase or atlest better exhaust note while it was in the car ?

Thanks mate

Was there a reason you removed it after a short time ? Did you notice any performance increase or atlest better exhaust note while it was in the car ?

Thanks mate

Removed as i was selling the car and had recently bought them and i wasnt gonna get much back after owning the car 3 yrs so took out a few bits and selling them.

Not sure about performance gains but it has a real good induction sound and exhaust got a tad bit louder too.

  • 1 month later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...