Jump to content
SAU Community

Recommended Posts

What's everyone do with seats in their M35? The standard ones look quite flat and not very supportive in corners. Anyone can confirm? So what would alternative options be? I take it theirs aftermarket rails so you could bolt in bride, recaro, sparco etc easily? Anyone know if V35, 350Z or any other performance Nissan seats would bolt in easily, whether using the stagea rail or the rail from the V35, 350 etc?

Link to comment
https://www.sau.com.au/forums/topic/461282-m35-seating-options/
Share on other sites

Ah yea pretty sure there's another guy with R35 seats Beregron or something like that I think. 350Z seats would be good if they weren't a huge headache. If they're a head then the gains aren't really worth it, probably better to go aftermarket

350z & V35 seats are the same design, you can get them in a bunch of different trims, material, leather, half n half and they are pretty much straight bolt in.

Biggest issue with my V35 seats was getting the wiring to work because the seats weren't electric beforehand but even that was a 15 minute job.

post-116816-0-68912300-1448508141_thumb.jpg

post-116816-0-93134800-1448508173_thumb.jpeg

I'm also looking at an M35 and wanted to look at options as I think the standard seats are probably fine and comfortable for the most part but I have a recaro in my current car and love how it hugs and holds me in. One look at M35 seats and you can see they aren't going to be amazing at holding you firm where you want to be.

Get it on the track or up in the mountains and you will be using your knees to hold your arse steady. You sit on the stock seats, not in them, and they are high enough that you stare at the rear vision mirror instead of the road. My seats dropped my arse at least 3 or 4 inches at a guess. I suppose it depends how fast you want to go around corners at the end of the day, and how tall you are.

Awesome, so all the bolt holes lined up?

Yep, lined up perfectly! No issues.

So why do people change there m35 seats? Are they just average or are you used to a different seat? Looking at purchasing a m35 I'm 6ft and 100kg. Is this a urgent change needed?

I'm 6'1 and not a light guy by any means, the stock seats although ok comfort wise are too high (head touches the roof) and have no side support, if you event half heartedly take a corner you'd slide everywhere. V35 seats are about 50mm lower and a hell of a lot more supportive.

Get it on the track or up in the mountains and you will be using your knees to hold your arse steady. You sit on the stock seats, not in them, and they are high enough that you stare at the rear vision mirror instead of the road. My seats dropped my arse at least 3 or 4 inches at a guess. I suppose it depends how fast you want to go around corners at the end of the day, and how tall you are.

For me its just below knees on outside resting against that pocket to hold myself gets annoying and sore after a while

Interesting you guys have trouble with height. I'm 5ft 10in and 92kg but I'm very short in the legs so have an upper body the length of someone about 6ft 2in, and I can get the seat low enough to have a decent amount of head room. My wife, who's only a fraction shorter than me (but in proportion so shorter in the body), jacks the seat up high and that starts to get tight but otherwise I've had no trouble with clearance. It took a while to get used to the base height after my Commodore but otherwise it's fine.

Maybe they changed for the facelift models?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...