Jump to content
SAU Community

Recommended Posts

Alright fellas, so, my car has been idling funny, missing and shutting down while idle etc. And it's come to my attention that its most likely the airflow meter.

Just wandering, will it make much, if any difference if i put an AFM suited for an rb25det, on an rb25de? im having a hard time finding an rb25de suited AFM on ebay.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/461296-air-flow-meter-query/
Share on other sites

I've heard green label, i checked mine and it was green label.

Also, today i tried unplugging it and running the car without one, but it ran like a piece of shit. basically ran the same as when it plays up, except when its connected it goes away for a while. (edit) just been informed this is due to limp mode.

Ill explain it so i can get a few more opinions;

When i start the car up cold is when it's at its worst, the idle will bounce up and down for a bit, sometimes sit at close to 2000rpm for a while, and i have to wait for the engine to heat up a bit before its driveable. if i try drive it before its warm, the car will stutter, and rev's behave as if they're hitting a limiter. if i idle and rev the car while its playing up, it will also behave as if it's hitting a limiter, at around 2500-3000 revs. recently its been quite hot and ive noticed the car has been able to drive straight away from a cold start, but in a cold climate it will play up.

The car will drive fine for a while once warm, and have the occasional miss and lose power for a bit, but it comes back. might do this a few times before back to normal. It hasnt been too bad recently in the hot weather. Also, when im idle, sometimes the engine will just die.

Thats all i can think of at the moment.

Edited by zac.r32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...