Jump to content
SAU Community

Jap To English Conversion

Philr32

By Philr32,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Hertz Donut Proficient

Hertz Donut

Posted
Posted

My pop-up screen doesn't, er, pop up, and doesn't respond to the "slap it on top" trick either, it's like there's no power to it or something. The DVD drive whirs on start-up but that's all. Is it simple to remove all this crap and fit a pocket? I've had the car for over 2 years and really haven't noticed not having the screen, so a little weight saving #becauseiwishitwasaracecar wouldn't hurt.

joshm35 Veteran

joshm35

Posted
Posted

No power is needed for these to pop up. The pocket is easy to install as it screws i to the same location with same holes. To get rid of the dvd rom you will need to find a panel with the pocket above the glovebox

  • 8 months later...
blade511 Contributor

blade511

Posted
Posted

Ok and here I go in a different thread but after spending sadly a half day of time going through all the pros, cons and options, I'm seeing the light and want to go pockets where the screen is and where dvd rom and etc are (unless I can Frankenstein a new touch screen into where the existing screen goes and do something funky there).. 

So apologies to all for pestering over the same questions, but am now super keen to find the pockets.. Suggestions ??

 

many thanks again for suffering me

Duncan Grand Master

Duncan

Posted
Posted

While its an F50 not an M35, I have a very similar screen and software, still in jap, and I use it all the time on the fuel economy screen.  No need to be aggressive in dismissing the questions from a new member just because you don't agree....why not just make your point politely and leave it at that?

 

joshm35 Veteran

joshm35

Posted
Posted
Ok and here I go in a different thread but after spending sadly a half day of time going through all the pros, cons and options, I'm seeing the light and want to go pockets where the screen is and where dvd rom and etc are (unless I can Frankenstein a new touch screen into where the existing screen goes and do something funky there).. 

So apologies to all for pestering over the same questions, but am now super keen to find the pockets.. Suggestions ??

 

many thanks again for suffering me


www.importmonster.com.au
joshm35 Veteran

joshm35

Posted
Posted

http://www.importmonster.com.au/view?url=http://page9.auctions.yahoo.co.jp/jp/auction/k217461415&thumb=http://auctions.c.yimg.jp/images.auctions.yahoo.co.jp/image/ra181/users/1/7/0/5/rath_1217_0830-thumb-146495754896359279290334.jpg&title=167%20M35

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...