Jump to content
SAU Community

Recommended Posts

I used to use my GT-R as a daily driver. It's a great way to get to know your car. BUT... the GT-R uses way too much fuel and gathers too much attention at times so I've just bought myself an EG (1995) Honda Civic (bulletproof) as my daily driver.

Here she is :cheers: It's a fun little thing. Very much opposite to the GT-R and it's VERY chuckable on street corners and roundabouts especially :)

low_03.jpg

One main issue is running costs - if you have the money to run a GTR 7 days a week..... why not??

Which is exactly why my Mitsubishi work van and my little Suzuki Sierra do so many kays. I'm not loaded and it doesn't take much to go wrong with a GTR before you end up with a 'second car' sized repair bill. Plus, since I've had mine I'd say it's been off the road more than on (the urge to mod gets ya) and I'm in the process of pulling the RB26 out for a rebuild (forged rods, pistons, metal head gasket, etc).

I live in the country and despite the lack of traffic, I don't think I'd want the heavy clutch, the hard ride or the exhaust drone everyday!

This is quite a hot topic! Keep up the comments and I "might" even reconsider using it as my daily.

But for all the people that are disagreeing so far, you might be able to tolerate such a difficult car to drive if you use it as a chellenge. My challenge is not to stall the engine at all in a week. Its been 3 months and counting but I STILL can't meet the challenge. Getting better now and I know that if I go to almost any other car, I'll be able to drive smoothly(example, my friends all drive with either heavy or multi plate clutches, 1st time in my car they were SO confident and guess what? They stalled it!)

Take the challenge and drive it daily! :)

But you might want another car handy on mondays! :cheers:

Here she is :cheers: It's a fun little thing. Very much opposite to the GT-R and it's VERY chuckable on street corners and roundabouts especially :)

You have a nice car there, the sort of car people would be proud to say it's their main car.

Owning two cars though can result in TWO sources of headaches.

If owning a Skyline makes one thing clear, it's that the Skyline is a car about BIG engineering, ie. BIG tyres, BIG wheels, BIG fuel needs.

Once you step down to a smaller car, you realise how things that cost $200 on a Skyline, costs $100 due to the fact you don't need the biggest or best.

I never stall my car even with the clutch but many people who drive it, even mechanics stall it so you're not alone.

I so wish for a small RWD car that can carry four people and a load and still give you a good sense of acceleration and handling.

T.

Hey T.

Buy a JDM AE86! :cheers: I miss my old one so much. It's a hatch so it can carry quite a bit with the rear seats down. The 4AGE is an awesome engine, revvy, punchy and it sounds so good. Rear wheels drive, lsd... man it's the most fun car I have probably ever driven!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...