Jump to content
SAU Community

Recommended Posts

Ahh I see what your talking about. The common way to get AUX sound into the M35 stock isn't to remove that cord, but to leave it in place a run an aux cord off the TV tuner in the rear LH boot trim. It sends a signal tho the screen and the screen in turn pushes the Audio out the head unit via that wire I believe.

Doing it this way you can also display video (NTSC in potato resolutions only though).

Or just upgrade the head unit, it's usually more cost effective.

  • 1 month later...

I would also run a new 12v wire to the clarion receivers in the boot roof to allow for a steady voltage feed and improved reception.

For my 1000th dumb noob question, what are the receivers you speak off? Receivers for TV or radio?

For my 1000th dumb noob question, what are the receivers you speak off? Receivers for TV or radio?

They are in the top rear passenger side of the rear roof lining. If you remove the rear roof panels you will see them (2). They amplify the signal from the glass
  • 3 months later...

Well just fitted a new Sony Head unit.

Took my time , used the Iso harnesses.

All went well, tested for sound before refitting everything.

Not much room behind the head unit for cables, especially with added iso plugs and leads.

Tucked in all in gently, put it ALL back together, now one speaker doesn't work.

Great.

Could be faullty head unit, faulty nissan iso harness, faulty sony harness or a break in one wire some where.

:angry:

Well just fitted a new Sony Head unit.

Took my time , used the Iso harnesses.

All went well, tested for sound before refitting everything.

Not much room behind the head unit for cables, especially with added iso plugs and leads.

Tucked in all in gently, put it ALL back together, now one speaker doesn't work.

Great.

Could be faullty head unit, faulty nissan iso harness, faulty sony harness or a break in one wire some where.

:angry:

If you tested it and everything work before you push the HU back in then maybe a wire got crunch/fell out soft of thing? Which ISO did you use?

  • 5 months later...
On 6/15/2016 at 0:30 PM, West said:

I"m the Aerpro man here, if you suspect the iso harness screw up, give me the part # and i can check for you.

Sorry to bother you. Can you advise me of the correct Aerpro part number for adapter cable to suit the Bose stereo model please? My plan is to simply feed an MP3 player into the system initially, then remove the CD-ROM drive and install a 'proper' car stereo. Mine is a 2001 M35 Stagea, BTW. I don't feel like spending a fortune ($500.00+?) replacing the whole centre section, just so I can fit a double DIN unit. 

19 hours ago, Zaphod said:

Sorry to bother you. Can you advise me of the correct Aerpro part number for adapter cable to suit the Bose stereo model please? My plan is to simply feed an MP3 player into the system initially, then remove the CD-ROM drive and install a 'proper' car stereo. Mine is a 2001 M35 Stagea, BTW. I don't feel like spending a fortune ($500.00+?) replacing the whole centre section, just so I can fit a double DIN unit. 

Sorry but i'm not 100% clear on what you're after.

You after ISO harness or T-harness?

If you want something like an RCA in so you can feed your MP3 player into the Unit, first of all, your unit needs to have an AUX button, then you can start from there.

I don't have a Bose HU in my stagea so i don't really know what they look like and what the rear plug looks like either.

On 11/23/2016 at 0:31 PM, West said:

Sorry but i'm not 100% clear on what you're after.

You after ISO harness or T-harness?

If you want something like an RCA in so you can feed your MP3 player into the Unit, first of all, your unit needs to have an AUX button, then you can start from there.

I don't have a Bose HU in my stagea so i don't really know what they look like and what the rear plug looks like either.

Since I have not pulled the stereo out yet, I don't know what I require. Sorry to be so vague. I am comfortable with electronics, so I can make pretty much anything work with anything, but I figured the Aerpro cable might make my life easier. See, I plan to do the whole job in a day (or two), so I wanted to have any adapters to hand before I start. I really don't want to strip the dash out, work out what is needed, reassemble, order the parts, then strip it all down again. Make sense? There is no AUX input on my Stagea stereo, though I was told it is a Bose system.  I have enclosed a photo of my Stagea stereo and the DVD ROM can be seen to the left of the photo. My plans are as follows (subject to change and not necessarily in this order):

* Rip out the stereo and the DVD-ROM drive. 

* Install a cheap radio/CD/MP3 player where the DVD-ROM drive is. 

* Locate the line level section of the cassette deck, break the line and terminate in a 3.5mm socket, so an i-phone/MP3 player can be plugged in.

* Integrate the radio/CD/MP3 player into the system.

* Install a new SATNAV/reversing camera somewhere.

 

BTW: I know what an ISO harness is, but not a "T-harness'.

 

Thanks for your advice and assistance. I am pretty new to Stagea ownership (2 weeks). 

 

Stagea.JPG

Edited by Zaphod
Brain fart

I see

Sounds like you just need a Nissan Bose to ISO, ISO to your HU brand, any Autobarn or SCA can help, i believe the boys here said nissan patrol iso harness will suit.

Not sure if Bose is any difference, you have built in Sub & Amp, if so then you might also need a low or high level converter.

I'm new to the Stagea myself, yet to pull the HU out to check as i'm going to set up GPS/Reverse cam but i'm lucky enough the car already comes with a Double Din Slot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...