Jump to content
SAU Community

Recommended Posts

Yep I have the same identical exhaust as Luis, the Fujitsubo

Legal my arse..

I have that exhaust with Scottys dump and 100 cell cat there is no way it is that loud. You can hardly hear it until i am well and truly up it.

Have you conducted your test in accordance with the RMS specs, and ensured that there are no hard surfaces within 20 metres to reflect any sound?

There is no way the Legalis is 114db.

Yep I have the same identical exhaust as Luis, the Fujitsubo

Legal my arse..

I have never heard a Fujitsubo get that loud.

I ran one on my previous M35 with an intake & dump pipe from Scott as well as a Kakimoto de-cat front pipe.

No chance in hell it hit 114db

My current VQ35 under full throttle with only the headers attached, sure.

I did the test at 5000 rpm, and the device was 1m away sitting on the driveway.

Exhaust was facing the street to so no reflecting surfaces.

I get 75 db inside the cabin.

With the windows down I get 85 db

Device is calibrated and gets normal conversation at 65 db so it's pretty good.

One thing... my cat is a single cell , if you get my drift

I'll get a 100 cell bullet cat, that should quiet it down a bit.

Also don't like the explosions of unburnt fuel on freeway driving.

This is what I have now.

post-25026-0-46897900-1452321598_thumb.jpg

Edited by conan7772

Thats a big suprise as i was suprised how quiet my Kakimoto Hypermega N1 is. Ill try and get cabin / exterior sound clip when i can. I also have the 62mm kakimoto silencer that can quiet it even more with no restrictions due to same internal diameter

Yeah but it will be loud and drony if made.

"if made badly or ignorantly"

I am getting a new exhaust made in the next few weeks. I'll try and post up how it sounds when done. I guess i could have just gotten a new dump / flex and joined the Fujitsubo crew but i like tackling things my own way with what i have at my disposal locally. Support the locals folks :)

If the bloke i am using's other work is an indication of what i'm in store for it should be a nice bit of kit.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...