Jump to content
SAU Community

Recommended Posts

I have of late been hearing various noises in my v36 coupe which seem to be related to the shocks. When I go over big bumps (as are common on Sydney roads) I hear a rattle. I now also have what sounds like a worn out mattress sound that is annoyingly common, and occurs over nearly every little flex of the suspension. I left the car with my mechanic, who despite looking quite carefully, was unable to locate any obvious source of the problem.

I have an adjustable coilover sports suspension set, that my mechanic says has no branding on it whatsoever (and thus likely a very cheap make - it is what the car came with).

Wasn't expecting this issue on a car with 68000kms (legitimate)...is my only option to replace the whole lot (shocks/springs etc)?

Is this a common v36 issue?

Link to comment
https://www.sau.com.au/forums/topic/463600-suspension-issues/
Share on other sites

My car (V36 coupe) arrived with lowered aftermarket suspension. Very high quality but not even close to being able to cope with Australian road conditions.

I now have a full set of MCA Coilovers made right here in Queensland and tuned for life on our roads. Cannot recommend them highly enough!!!

Check the front lower control arm bushes. Very common on V36s and on the sister infinities... You won't be able to see wear in the bush but if you glide slowly (slow slow walking pace) and jam on the brakes you might see the wheel jump back an inch or more (towards the rear of the car)... This is wear in the LCA bushes.

Unfortunately if it is this then it's not cheap - they don't sell the bushes separately and you are up for two new LCAs. I just did mine at a cost (NZD) of $1700ish.

For what it's worth I was a little skeptical before but it noticably improved steering and braking.

Cheers - N

Check the front lower control arm bushes. Very common on V36s and on the sister infinities... You won't be able to see wear in the bush but if you glide slowly (slow slow walking pace) and jam on the brakes you might see the wheel jump back an inch or more (towards the rear of the car)... This is wear in the LCA bushes.

Unfortunately if it is this then it's not cheap - they don't sell the bushes separately and you are up for two new LCAs. I just did mine at a cost (NZD) of $1700ish.

For what it's worth I was a little skeptical before but it noticably improved steering and braking.

Hmmm?? I have recently replaced these bushes on my 2003, V35. Check out Spares Box.com.au They sell Super Pro, I have just done a quick search of the site using a 2007 car as an example which should cover the V36, and the product is for sale for < $200 AUD\set. Part No. SPF2847K Their website can be difficult to search on. Probably best look it up as a 350Z

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...