Jump to content
SAU Community

Bathurst In December


260DET
 Share

Recommended Posts

The regularity time has been reduced from 2.40, to 2.36 I think but would have to check that to make sure of the exact time.

Most of us who are doing regularity normally do sprints but the general consensus is that, particularly for first timers like me, the Bathurst experience is the most important thing. It's not like we will be going slow, my V8 Zed should be capable of 260kph there with a 3.69 diff. One of our lot who is quite experienced has a race prepared 370Z, he intends to do the sprints.

Link to comment
Share on other sites

Hope the groups do work out well and the traffic problems I'm imagining don't happen - it's just too much money for me to take the risk. I don't have the money now anyway - just bought another car and the Soarer's up for sale.

Is the V8 up and running now Richard?

Link to comment
Share on other sites

What have you bought now Harry? Hard to keep up with your purchases :)

Sorting out the TCU (transmission control unit) is just about done now for the Z, what a PITA that has been. But I love the result, it would not suit everyone but it suits me and it's bloody fast.

Link to comment
Share on other sites

pretty much the exact opposite of a Soarer - SW20 MR2 with Camry 3VZ-FE 3.0 V6, light flywheel, Quaiffe diff, coilovers... slower, but I imagine it will be far more "involving" to drive :) Only had it for a day, but it's an event just driving it in traffic - can't wait to get it out on some decent roads this weekend!

Edited by hrd-hr30
Link to comment
Share on other sites

Nothing much: Torsen, BC coilovers (I changed the front spring rate), stainless exhaust, FMIC, transmission cooler, HKS SLD & FCD, 18x9.5 and 10.5s

Series II, Black on black - so no horrible multi-tone brown or green interior... but pov pack cloth trim, no sunroof. SAAS fixed position drivers seat and JZA80 passenger seat (stock seats included). Pretty average paint and some no f**ks given hacks for track cooling and stuff... Mechanically A1 $4800 as it is, but I might pull some bits out of it and throw a stock front bar on before selling it a little cheaper - plywood ducting may not be for everyone...

post-15659-0-76177900-1460683534_thumb.jpg

Edited by hrd-hr30
Link to comment
Share on other sites

A MR2 eh Harry, you like a handling challenge, looks like you have one right there :)

We didn't struggle "too much" with setting one up to handle respectably.

The challenge is in adapting to driving them correctly. Rear weight bias changes things, but there's enough video of Porsche 911 and Lancia 037 on gravel to show what rear engine cars can do.

Link to comment
Share on other sites

I think the handling 'issues' are a common misconception. Proper motoring journos (ie the ones who could drive - like Tiff Needell) raved about them when they were first released, and they were untouchable in their class (NA sports cars) at Bathurst's 12hr Production car races - even ending up with a 4th outright.

Link to comment
Share on other sites

lol I may have neglected to mention it got it's 4th outright mainly through fuel economy and not having to change brake pads like all the big powerful cars.

Stock Camry power is not going to get anywhere near 60 sec! And that's not what the car's about anyway. It's about the rorty NA engine, razor sharp handling, and enjoying a totally different driving experience.

Link to comment
Share on other sites

Lol the 'razor sharp handling' and any twin cam three litre engine in a smallish modern chassis adds up to good lap times, there have been a few under 60 sec Lakeside laps done by older inferior spec cars as you well know Harry so the expectations are high and the pressure is on :yes: Don't cop out by using crappy tyres either, I'm watching.

Link to comment
Share on other sites

you've got no idea... It's just a 200bhp mid 90s 3VZ Camry motor. Power to weight is about the same as an 86. They've got pretty sharp handling too. With suspension setup by the best - MCA, and Josh Coote driving, they run 63s. I'll be happy around that.

And crappy tyres are my trademark! So you're going to be dissapointed :P

But it's not really about Lakeside, or any other track for that matter. It's just for the fun of it, and for the totally different driving experience of a small, light(ish), rorty naturally aspirated mid engined car.

Link to comment
Share on other sites

63's!!! Old Zed cars do that, the very best do under 60's. The best driving experiences I've ever had were when pushing it around Lakeside, street driving has no comparison, you must be getting soft Harry :)

Link to comment
Share on other sites

Latest on the topic has 300+ drivers registered with the organiser of which 49 are on the Z Car Club Q regularity list. So, as expected, this event is 'selling out' quickly. If want to get on the Z list then I suggest you contact Dave toot sweet.

Link to comment
Share on other sites

63's!!! Old Zed cars do that, the very best do under 60's. The best driving experiences I've ever had were when pushing it around Lakeside, street driving has no comparison, you must be getting soft Harry :)

Funny - it takes some Zeds that weigh less than this MR2 over 450rwbhp to just barely sneak into a 59 on one single lap ever... Not to mention expensive MCA suspension, aero and years and years of trying...

And the old "280Z" cheater spec race car Zed that held the Class S sportscar lap record ran a best of 64, and it just sold for approximately 12 times the cost of this everyday road car MR2...

The only two old Zeds powered by Datsun motors to ever break 60 sec both have 3.3l $30K motors alone and needed super soft slick tyres to do it...

Edited by hrd-hr30
Link to comment
Share on other sites

Plenty of average spec Zeds doing 63's though Harry, costs can't be compared because a pretty ordinary standard Zed will bring ~$15k and it costs a lot just to bring one up to specs that all modern cars have except for their good stiff chassis.

When I heard of the best time the 86 you mention did I was pretty suprised, thought it would do better than that. Lol at the '280Z', I used to rubbish him for being one of the slowest Zeds out there but Lakeside is a lot about the driver and maintaining momentum as you well know.

Link to comment
Share on other sites

Plenty of average spec Zeds doing 63's though Harry

There should be - hundreds of kilos lighter and capable of as much power as the MR2 easily, with cheap easy 'average' brake upgrades etc, but there's certainly not "plenty". Unless 2 or 3 counts as plenty in your books... and by average, you mean only the fastest of the state's Zeds that are basically race cars...

Edited by hrd-hr30
Link to comment
Share on other sites

86's are pretty good, I hung onto one for a lap and a bit with the crappy running Zed the other day at Morgan Park, it was a Neal Bates 86 race series spec one and being driven by Glenn Seton, boy am I dropping some names here lol. Anyway, it's handling and acceleration showed no sign of it being over weight or having any other impediment, went like a 60 second Lakeside lap car in my humble............ Only sorry that I didn't have the incar camera going.

Link to comment
Share on other sites

edit: nevermind...

but now my MR2 road car should 'easily' be faster than the lighter, more powerful 86 race car with a Pro driver...

Edited by hrd-hr30
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • The stock one will outperform any aftermarket standard position exhaust manifold. If you don't believe me, do a back to back test (same turbo, same boost, same timing) and you'll be super surprised.
    • Any recommendations on a decent replacement manifold that doesnt break the bank or require additional mods for the stock turbo setup? I figure if I'm going to pull the manifold off anyway to fix the studs might as well replace it. 
    • So I checked the turbo out today. Very minimum play at all just enough for the oil to take up when it's running. I did find an exhaust leak at the manifold. 1 stud all the way in the front is missing and the one all the way in the back is broken off. Front has visible signs of an exhaust leak. I'll fix that soon but that's not my problem still.  I also found that the nipple coming off the turbo had the hose capped off and a hose ran from the j-pipe by the bov going to the wastegate. I removed that hose and capped that nipple and put the turbo nipple hose back on the wastegate.  There was a ton of oil residue all through the charge side of the intercooler piping going to the throttle bodg. I'm thinking that's from the pcv. Doesn't seem to be coming from the turbo that was all clean on the pipes side.  Haven't had a chance to check fuel pressure yet, haven't had time been having to pull a lot of doubles at work. I did pick up some carb cleaner to clean the iacv but wanted to make sure I had a fresh gasket in case the old one rips when I pull it off.  I'm waiting on a MAF that was supposed to be here today but delayed to Monday. Have a double Monday and Friday and work all of next weekend so going to try to find some time in the middle of the week to try that out. Did about a 10m trip around the block today and towards the end the issues were coming back. Fingers crossed on this MAF but if not just going to throw a fuel pressure gauge in and see where I'm at.  Did notice today that I can definitely hear the injectors pulsing. Very audible clicking coming from them. Assuming that's normal? Should also mean CAS is functioning somewhat properly. After it warmed up when I started it the intermittent misfires came in again. Did start doing that before it was fully warmed up. 
    • This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
×
×
  • Create New...