Jump to content
SAU Community

Greddy Engine Oil Block Type E - Bnr32

WantGTR

By WantGTR,
in Engines & Forced Induction

 Share

Recommended Posts

WantGTR Mentor

WantGTR

Posted
Posted

Hi all,

thinking about buying one of these for an oil cooler set up. i like the built in thermostat and i really dont want to fit a relocator.

the hicas is removed so there is more room.

does anyone here have it fitted to there bnr32? to me it looks like there isnt enough room. am i wrong?

pic of said sandwhich plate

nengun-3025-04-greddy-oil_sensor_adapter

HarrisRacing Proficient

HarrisRacing

Posted
Posted

Hi all,

thinking about buying one of these for an oil cooler set up. i like the built in thermostat and i really dont want to fit a relocator.

the hicas is removed so there is more room.

does anyone here have it fitted to there bnr32? to me it looks like there isnt enough room. am i wrong?

pic of said sandwhich plate

nengun-3025-04-greddy-oil_sensor_adapter

Pictures and information in my build thread on page 6. NO CLUE about factory manifold and such, but I'm sure it's possible. I had mine in several different arrangements starting with your idea, and then moving to the final idea of relocating the oil filter as well... Note where my temp pickup is located, this is on the RETURN side from the oil cooler so that you know what the temp of the oil is going into the engine.

Borci88 Veteran

Borci88

Posted
Posted

Need to remove standard oil cooler

The heat exchanger? You don't. I've fitted a few of these now to 32, 33 and 34 and they all fit. They're a little annoying because where the cooler hose comes from is very close to the engine mount, I'm talking 1cm close. It can be done and they're actually a great piece of kit that after fitting 10+ of them I put one on mine as well.

GTR_JOEY Grand Master

GTR_JOEY

Posted
Posted

The heat exchanger? You don't. I've fitted a few of these now to 32, 33 and 34 and they all fit. They're a little annoying because where the cooler hose comes from is very close to the engine mount, I'm talking 1cm close. It can be done and they're actually a great piece of kit that after fitting 10+ of them I put one on mine as well.

Well there you go

HarrisRacing Proficient

HarrisRacing

Posted
Posted

Also the two additional fittings they send are blanked. They also sell some that are tapped 1/8 but this is NOT NPT, it's PT (Japanese). I drilled and tapped my blank ones for my temp and pressure sensor pickups.

WantGTR Mentor

WantGTR

Posted
  • Author
Posted

was thinking that.

i noticed the coolers with the -10 outlets are considerable cheaper than the -12 ones.

im thinking most people buy the -10 ones?

in my mind im thinking bigger is better, no?

what are peoples thoughts on buying a oil cooler with -10 outlets and buying a -10 to -12 hose end?

wildeagle44 Collaborator

wildeagle44

Posted
Posted

was thinking that.

i noticed the coolers with the -10 outlets are considerable cheaper than the -12 ones.

im thinking most people buy the -10 ones?

in my mind im thinking bigger is better, no?

what are peoples thoughts on buying a oil cooler with -10 outlets and buying a -10 to -12 hose end?

Also interested in reasoning of -10 vs -12

I would have thought you may see a pressure drop?

wld093 Contributor

wld093

Posted
Posted (edited)

In the process of fitting my oil cooler setup without relocation. Extra parts required on top of kit was

oil filter stud - purchased from kudos Motorsport

Trust/greedy sensor adapter to fit factory oil pressure sender. The oil temp sensor won't fit unless you get an adapter to step up. I am going to be running aftermarket oil temp/pressure gauge which will come with correct sensor fitting 1/8 npt if I'm not mistaken.

I have not fitted a relief valve to my N1 block but will be running a filter that runs one.

I have chosen to remove the heat exchanger but this is not a must. Clears up a lot of space which I like. Obviously the factory coolant lines that feed heat exchanger will need to be bunged if going down this path.

Manifold is fitted in photo.

post-100155-14615772869524_thumb.jpgpost-100155-14615772996771_thumb.jpg

Edited by wld093
HarrisRacing Proficient

HarrisRacing

Posted
Posted

Also interested in reasoning of -10 vs -12

I would have thought you may see a pressure drop?

1) I don't think the hole from the block that sends oil is 1/2" in diameter but it's been a while since I looked at it. -10AN is approximately .5" in diameter and is AMPLE (IMO) for the oil flow in most engines unless you are running something crazy I don't know about.

2) The Greddy kit fittings are -10AN fittings. I'd assume they would send -12AN if it were required for our engines.

WantGTR Mentor

WantGTR

Posted
  • Author
Posted

In the process of fitting my oil cooler setup without relocation. Extra parts required on top of kit was

oil filter stud - purchased from kudos Motorsport

Trust/greedy sensor adapter to fit factory oil pressure sender. The oil temp sensor won't fit unless you get an adapter to step up. I am going to be running aftermarket oil temp/pressure gauge which will come with correct sensor fitting 1/8 npt if I'm not mistaken.

I have not fitted a relief valve to my N1 block but will be running a filter that runs one.

I have chosen to remove the heat exchanger but this is not a must. Clears up a lot of space which I like. Obviously the factory coolant lines that feed heat exchanger will need to be bunged if going down this path.

Manifold is fitted in photo.

looks great. from the replies in this thread i have decided to keep the factory heat exchanger so i dont see why i would need the additional sensor adapter. i was however under the impression that the sandwhich plate came with a stud. ill have to check what i have bought.

1) I don't think the hole from the block that sends oil is 1/2" in diameter but it's been a while since I looked at it. -10AN is approximately .5" in diameter and is AMPLE (IMO) for the oil flow in most engines unless you are running something crazy I don't know about.

2) The Greddy kit fittings are -10AN fittings. I'd assume they would send -12AN if it were required for our engines.

after all that i bought i the -12 version. ill be going -12 everything.

HarrisRacing Proficient

HarrisRacing

Posted
Posted

I am wondering what the oil flow is if you have the factory exchanger in place. I have mine laying around and may want to see what the flow is doing before you decide to leave it. If it's first in line the temp reading won't be what's actually going back into the engine and if it's last in line the work from your external cooler would be undone from the exchanger reheating it.

Just a thought. Oil flows out from the block on the outside of the oil boss and back into the engine through the center bolt FYI.

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
    • DannyDee2
      First time owner v35

      By DannyDee2 · Posted

      Welcome mate!
    • DannyDee2
      Trans oil cooler off a Stagea

      By DannyDee2 · Posted

      I'm interested,do you still have it?
    • luke gtr
      First time owner v35

      By luke gtr · Posted

      Deutz v8?
×
×
  • Create New...