Jump to content
SAU Community

Recommended Posts

13 hours ago, darcyy said:

Yes, But they only work on Aus delivered nissans!

Locksmith couldn't reprogram it because the CEL is not working  

Do you have another dealership you can go to?

Most Nissan dealerships will work on imports

On 7/5/2016 at 6:52 AM, KiwiRS4T said:

What about a non-franchise shop that works on Nissans and has a Consult tool?

 

On 7/5/2016 at 11:39 AM, iamhe77 said:

Do you have another dealership you can go to?

Most Nissan dealerships will work on imports

None want anything to do with it.

Just had it on a scan tool, body control module code is coming up. Is nissan the only place to get it re-coded?

Mate of mine had to have his V35 BCM replaced which obviously meant re-coding.

It was a 30 minute job - replace and re-code at Nissan.

As far as I know, yes, only at Nissan but then I am unfamiliar with most scan tools. Maybe ask around if anyone local has Snap-on or a Consult 3/4. Consult will do the job, but unsure as to the Snap-on.

Also, where are you located?

  • 2 weeks later...
On 7/6/2016 at 5:06 PM, iamhe77 said:

Mate of mine had to have his V35 BCM replaced which obviously meant re-coding.

It was a 30 minute job - replace and re-code at Nissan.

As far as I know, yes, only at Nissan but then I am unfamiliar with most scan tools. Maybe ask around if anyone local has Snap-on or a Consult 3/4. Consult will do the job, but unsure as to the Snap-on.

Also, where are you located?

Sorry for the late reply!

Did his require a brand new BCM or would a used one work as well?

Had a locksmith try to recode it but couldn't due to the check engine light not working,

Im northside brisbane

On 7/16/2016 at 1:04 AM, darcyy said:

Sorry for the late reply!

Did his require a brand new BCM or would a used one work as well?

Had a locksmith try to recode it but couldn't due to the check engine light not working,

Im northside brisbane

New BCM as his was stuffed.

Quoted from his text message:

"cost was $300 and something + fitting. Can't remember price, but wasn't too bad for fitting as it is all plug in shit and easy for them to program with consult"

He had Ferntree Gull Nissan (VIC) do the lot. Maybe you need to find a competent Nissan dealership or at least a mech with access to consult?

  • 2 weeks later...
On 7/17/2016 at 6:29 PM, iamhe77 said:

New BCM as his was stuffed.

Quoted from his text message:

"cost was $300 and something + fitting. Can't remember price, but wasn't too bad for fitting as it is all plug in shit and easy for them to program with consult"

He had Ferntree Gull Nissan (VIC) do the lot. Maybe you need to find a competent Nissan dealership or at least a mech with access to consult?

ok will swap in a new BCM and take it to nissan to get re-coded

Thanks for the help

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...