Jump to content
SAU Community

Recommended Posts

Hello everyone I'm Paul from the uk.

Been the proud owner of an r33 gtst spec 2 auto in sonic silver for 2.5 years now and i've been looking at upping power.

Went to santa pod raceway this weekend to see what the car would do with some like minded owners sadly things didn't go to plan so to cut a long story short I was on my way home and suddenly lost drive, blipped it and the revs jumped up but the car didn't respond and just carried on doing the same speed. I coasted around 100M to where I could pull off the road, as I did I could smell burning :(

Jumped out to find ATF down the side of the car and a split hose from my oil cooler, it was still running out.

Managed to organise some ATF and bodge the hose by bypassing the cooler, drove home with tail between legs and took it very easy.

My question is how much damage have i done? any? none? new box? the oil was still nice and red that was coming out but it did pong a bit. once topped up the box "seemed" fine but I didn't take her above 3k rpm.

I'm going to hazard a guess and say I should take it out, get it into third and give it some therapy and see if it slips at all.

Any other suggestions to tell?

I'm truly gutted.

 

 

Link to comment
https://www.sau.com.au/forums/topic/465759-busted-trans/
Share on other sites

Yea I just took it nice and easy all the way, box seemed fine but I can't help but worry about it, push comes to shove I'll have to get another box beauty of that is nobody wants auto boxes so they're dead cheap. There was a couple on eBay one for £25 and another for £45 where as the manual boxes go for between £500 and £700 !!

I'm relocating the oil cooler tonight to a more suitable position, then I'll get her out and see, fingers crossed......

Link to comment
https://www.sau.com.au/forums/topic/465759-busted-trans/#findComment-7757644
Share on other sites

Right, pulled my tranny cooler set up to pieces today and and repositioned it all.

Just topping up the fluid and looking for answers on the net but there's nothing definite so...

do I check the level with the engine idling cold? Or hot?

or

do I check the level with the engine off cold? Or hot?

or all four?? Lol

Sorry there's not many auto owners over here in the uk.

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/465759-busted-trans/#findComment-7757962
Share on other sites

When the line popped I topped up with 3 litres, the trans came back to life, well it got me home driving gently. The fluid was around 20 miles old no more than that. Topped back up yesterday and tried the dipstick when it was warm and idling it was low, barely registering in fact, turned engine off waited five minutes for it to settle and it measuresd perfect for  a hot engine.

So it's a bit confusing, really want to get this sorted so I can take the car out and see if the box is damaged after what happened.

thanks for everyone's input on this, much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/465759-busted-trans/#findComment-7758057
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agree with Rob. I recently did mine and replacing with a brand new unit made the most sense compared with rebuilding my existing gearbox.
    • Are you suggesting that the kit did a cheap and nasty job of just jamming the wheel in between other things and caused the misalignment? I mean, we normally do this with an integrated crank trigger wheel, not something bodged on. It's not 1995 any more.
    • I mean, given the number of BMWs you own their tolerance for improper torque is rather low. The number of torque + angle spec bolts and non-reusable bolts in one is nuts.
    • Atmospheric vent requires something that doesn't use a MAF for load. You would need a standalone ECU for that.
    • Hey all,   I’ve got an RB25 with a trigger kit that includes a crank wheel, and I’ve hit a wall trying to sort a timing belt tracking issue. The belt either rides right on the edge of the cam/crank pulleys or walks slightly forward once the engine starts. It tracks okay-ish for a moment, then creeps right to the edge—and honestly, it’s stressing me out.   I’ve spent hours removing and reinstalling the belt, double-checking everything:   Tensioner setup is good, checked multiple times Idler pulley and washers are all in the correct places Followed the RB25 timing procedure step-by-step     The only thing I changed was the rear crank washer—I swapped the OEM one for a Neato version, and it made things worse. The belt now sits even more forward than before. I’m beginning to think the crank trigger wheel itself (from the trigger kit) is the issue—poor design or slightly off dimensions.   What’s strange is that with the previous belt setup, it actually ran fine for a couple of years—around 4,000 to 5,000 miles, even with hard driving and high RPMs. But even then, the belt was always riding right on the edge, and I know that’s not ideal or safe long term.   At this point, I’m debating whether to:   Machine a few mm off the crank trigger wheel to bring it back in line, or Replace it entirely with a better-designed unit     Only thing is, I already have the Cherry Hall sensors, bracket, etc.—I just want to replace the wheel only, not the entire kit. Anyone know a brand or supplier that sells just the crank trigger wheel on its own?   Would really appreciate any feedback—especially from anyone who’s run into this exact issue and found a reliable fix.   Thanks in advance.
×
×
  • Create New...