Jump to content
SAU Community

MCA Coilovers - knocking

pureplaya
 Share

Recommended Posts

scott anderson Newbie

scott anderson

Posted
Posted
On 7/13/2016 at 12:49 PM, pureplaya said:

Hi All,

I recently got a full set of MCA X-R series coilovers supplied and installed on my R32 GTR by a reputable suspension place in Sydney. 

Left rear coilover is knocking on almost every single bump. The mechanics knew there was a knock and checked over every nut and bolt related to the suspension. All seemed fine.

They are currently ordering a new replacement set for the rears as there is possibly something loose within the coilover assembly.

Just wondering has anyone experienced a similar issue with MCA coilovers?

Also any advice to somehow soften the ride slightly. Sydney roads are horrible and the standard setup is a bit too bumpy for my liking.

Cheers

Kase

 

scott anderson Newbie

scott anderson

Posted
Posted
On 7/13/2016 at 12:49 PM, pureplaya said:

Hi All,

I recently got a full set of MCA X-R series coilovers supplied and installed on my R32 GTR by a reputable suspension place in Sydney. 

Left rear coilover is knocking on almost every single bump. The mechanics knew there was a knock and checked over every nut and bolt related to the suspension. All seemed fine.

They are currently ordering a new replacement set for the rears as there is possibly something loose within the coilover assembly.

Just wondering has anyone experienced a similar issue with MCA coilovers?

Also any advice to somehow soften the ride slightly. Sydney roads are horrible and the standard setup is a bit too bumpy for my liking.

Cheers

Kase

I had a similar experience with a set of MCA Blue coilovers (GT 86) purchased/installed at Vsport. Knock  developed and inspected by MRT Rhodes workshop at next service. Fixed? under warranty by Vsport and have noticed knock returning. Haven't approached Vsport about it yet, but after reading your post, I'm wondering if the problem is caused by the installation or the product?                                                                                                                                                                     Any info regarding this subject appreciated.

  • 2 months later...
Russlancer Rookie

Russlancer

Posted
Posted

Hey guys I need some advice am getting a second hand set of MCA X-R looks to never been used my question is they came off an ralliart Evo I have an Lancer LX well I be able to have them fitted to my car am not a huge car guy to do track and big modification but am getting these really cheap like for $250 so with knowing they can sell over $2k I brought them cheers any recommendations would be appreciated here is a pic of them.

IMG_20180919_131355.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...