Jump to content
SAU Community

What is this swith for? ? 260rs

livewire

By livewire,
in Four Door Family & Wagoneers

 Share

Recommended Posts

livewire Experienced

livewire

Posted
Posted

Hey guys. I just purchased an autech 260rs and came across a little switch on the drivers side kick panel near accelerator pedal. It kinda looks factory as the 'off' writing isnt a sticker or painted on by hand. I innitially thought it may be a kill switch but after testing its not. Does anyone else have this switch or know what it could be?

Thanks

20160722_140857.jpg

Link to comment
https://www.sau.com.au/forums/topic/465935-what-is-this-swith-for-%3F-260rs/
Share on other sites
Cowboy1600 Grand Master

Cowboy1600

Posted
Posted

At a guess it's the 2wd switch.  Turn ignition on, flick it to OFF, start car, pump brake pedal 5 times.  Does 4wd light come on?

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
3 hours ago, livewire said:

I'll give that a go when i get a chance. I didnt know you could actually have a 2wd switch fitted. 

Any ideas on diff lock switch?

There is no diff lock in the Atessa scheme of things. There is a switch which will give you a 50/50 fore and aft power split but that only operates at low speeds for e.g. getting you out of a muddy paddock or up a boat ramp. As soon as you hit 20 km/hr or so it reverts to the stock 95% rear until the rear wheels start to spin.

The 2wd switch (if that's what it is...its not a factory item someone had to install it to save you pulling the plug behind the driver's kick panel)  works as described by Aaron but it only works until you turn  the engine off and then you have to set it again. From the manual:

Locate the "air bleed" wire behind the drivers kick panel, it's a plug with a single wire either side (usually green socket, white plug).

Disconnect it.

Start car. As key comes back to the ON position, within 10 seconds, depress brake pedal 5 times, 4WD light will start flashing to indicate you are in 2WD mode.

To go back to 4WD mode, turn car off, reconnect plug and off you go.

 

 

TMLP Community Regular

TMLP

Posted
Posted

I have a 260RS THERE IS NO  diff lock button there are few things incorrect in that page of info Dont take it as gospel if yours doesn't match. 

I also have 2 switches over my door near my head I the roof liner. NO idea what they do either. 

Duncan Grand Master

Duncan

Posted
Posted

Yeah I guess the diff lock button must be a 260RS thing because all the other models have them; strange to exclude because I wasn't aware of any other difference in the ATTESSA system.

 

The only switches normally on the roof are sunroof or courtesy lights

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

The article is wrong there is no diff lock in the RB world and hence no diff lock button. The idea probably comes from a misunderstanding of the function of the switch I described above which is common to all attessa equipped Stageas. The Attessa reservoir is not an exclusively  260RS feature it is a feature of all awd Stageas.

  • Like 1
Gezza1er Newbie

Gezza1er

Posted
Posted

HAHA my Autech is in this Article. Very 1st pic from Fuji. My S2 Autech also had a switch that looks like yours but near my rear fog light switch. looked to see what it did. was just connected to a earth so i pull that out. just thought i would add my 2 cents.

 

  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • StevenJames32
      Single Turbo Conversion On R32 GTR.

      By StevenJames32 · Posted

      Hi everyone, I'm about to complete my first single turbo conversion on my R32 GTR and I thought I would post the step by steps that I will be following. I will list the parts I have / the parts I will be buying. I will be redoing this guide after I have completed the conversion. Parts list: - 3576 turbo 0.82 v-band (coolant and oil)  - v-band top mount turbo manifold - 50mm wastegate - manifold copper gasket - titanium manifold stud kit - turbosmart 3 port boost solenoid - link can lambda kit (wideband) - link ECU - radium 12AN push in valve cover fittings (pair) - hi octane catch can - 3.5inch downpipe - screamer pipe - pipe from turbo to intercooler - intake pipe setup - power steering relocation kit - oil drain block off plate - coolant and oil lines Now onto the step by step guide (please add / correct me if there's anything I missed: 1. remove fluids, twin turbo pipes, pod filters and afm's 2. remove the factory coolant hardlines from the hot side. 3. remove heat shields  4. remove the downpipe 5. remove turbos and manifolds 6. remove factory manifold studs 7. clean whatever mess you have made 8. install power steering relocation kit 9. install new manifold studs 10. install new turbo manifold with gasket 11. install new wastegate with screamer pipe 12. install new turbo  13. install new coolant and oil lines  14. install rear oil drain block off plate 15. stop and appreciate that you now have a single turbo in your GTR 16. wipe away tears of joy and install downpipe 17. install the wideband sensor into downpipe 18.install pipe to connect turbo to intercooler 19 .remove stock boost solenoid  20. install new boost solenoid 21.  install intake setup 22. setup the rest of the can lambda kit with the ecu  23. refill fluids and hope for the best 24. ask forums for help with issues 25. fix issues 26. drive your single turbo swapped r32 GTR into the sunset. Doneeeeeeeeeee. Now I know this isn't detailed at all but I will be doing that when the conversion is done. I will be posting pics and any helpful details i can and ill make sure to fit in as much information as I can. If there's anything I should know before i do this PLEASE let me know. Stay tuned for what's next. Thanks...
    • tidi0x
      Nismo GT Pro LSD configurations

      By tidi0x · Posted

      I have wasted too much time on this, more than I am willing to admit. I hope someone can set the record straight for me.  I want to replace my Nismo (non GT pro, non GT) standard 2 way in my R33 GTST with a 1.5 way... Ideally I want to get an ATS 1.5 way Carbon LSD, but I don't want to reuse my 29 spline 5x1 axle stubs, and new 30 spline 5x1's are impossible to get a hold of ($$$), and I don't want to drop the cash on going to 6x1 stubs and axles ATM. Which leads me to the Nismo GT Pro 38420-RSS15-B5 or RSS20, as they come with new axle stubs meant for the diff, and is "Convertible" from a 2 way or 1.5 way to "Other ways", but that is where I am stuck as the documentation is a bit all over the place.  To sum up what I have found I believe the all the Nismo GT Pro PN's are convertible from 2 way, 1.5 way, and 1 way; but Nismo sells 2 skus (2 & 1.5) so people do not have to disassemble to convert it.  I found this thread on 350z but it left the question unanswered. https://my350z.com/forum/engine-and-drivetrain/620032-nismo-gt-pro-lsd-1-5-vs-2-way-and-torque.html  Essentially the way I think it all works out is like follows...  2 way  1 way  and 1.5 way would be the center pinion shaft in the 1 way block, but with the with the center flipped 180*. So the ramped side of the pinion would face the 1 way gate and act like a ramp.    I can only get my hands on the 2 way in the states, and I am not trying to get stuffed on tariffs by ordering from Japan or anywhere else. I want to confirm that if I get the 2 way I can convert it to the 1.5.     
    • StevenJames32
      Single Turbo Conversion On R32 GTR.

      By StevenJames32 · Posted

      Hi everyone, I have purchased my first GTR and I want to do a single turbo conversion to it. I've been doing as much research as i can and there are a few things that I can find and need to know. I need to run a coolant feed, coolant return, oil feed and oil return for my turbo setup. Here's what I know so far: On the hot side of the rb26 there is coolant feed, oil feed and oil return. Coolant return will be going around the front of the engine to where the thermostat is located. I will need to block off the rear oil return port. I will be running a turbosmart boost solenoid so any of the factory boost stuff wont be needed. Now onto what I don't know: 1. What do I do with the coolant / vacuum hardlines that run around the back of the motor?. 2. What do I block off or loop or move or remove?. I will be running the OEM intake manifold. 3. Is there anything in particular I need to buy for the cold side of the rb26?. I already have the intercooler and pipes sorted. If you have any pictures or information it would be appreciated. Thanks....  
    • Murray_Calavera
      "Cheap" bolt on turbo on RB25DET NEO

      By Murray_Calavera · Posted

      The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • joshuaho96
      "Cheap" bolt on turbo on RB25DET NEO

      By joshuaho96 · Posted

      Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
×
×
  • Create New...