Jump to content
SAU Community

Recommended Posts

So any help appreciated guys,

There's countless posts on misfiring on this site and I've viewed most of the ones I've found, to no avail.

Engine details:                                           RB25DET S1.5, ECU is Haltech E11V2, running a MAFless tune, Garrett GT3582R, Upgraded Intercooler, GFB manual Boost controller, Tial EWG 63mm, Nismo 740cc injectors, 3BAR MAP sensor, Bosch 040 fuel pump, Sard adjustable fuel reg (with gauge (set at 55psi) HKS Oil cooler and remote Oil filter, Splitfire Coils, NGK Copper plugs gapped at .8 with 21KMs on them.

So car developed a missfire last week, over fueling, hesitating at all operating temps (biggest from TPS 0 to >2) from startup to shut down with a rich and lean pops in exhaust, surging during acelleration and cruising. Checked usual culprits in order; Coils, Plugs, Tune re install, Vacume and hoses, Fuel Reg, Compression test, Injectors Flow tested and inspected All okay, TPS sensor, Coolant temp sensor, Air Temp sensor, MAP sensor, related wiring, AAC valve, replaced Fuel filter, and ECU checks out.

Nowe I havnt done the CAS, as I was under impression that a faulty cas will cause problems with starting, and it starts like nothings wrong. The BOV has been on for 4 years (was on car when I got it) and never had an issue with it before) have checked to make shure Diaphragm in Fuel reg isn't totalled and it's all fine. And no it hasn't had an o2 sensor on the exhaust (ecu) since acquiring it. The air fuel mix at idle is around 10.8:1 richining on throttle depress. All sensor have been tested with Multimeter and viewing on the Ecu both are in sync.

Cars in Red Center Nats in a month so would like to have it run by then.

Any help appreciated                                             

Edited by KittoRB25
Grammar
Link to comment
https://www.sau.com.au/forums/topic/466085-missfire-rb25det-mafless-tune/
Share on other sites

Cheers, taken off and no audible sound from the CAS, also checked on the Ecu and it's providing a response to the ecu.

Edited by KittoRB25
Development

check your base timing and if it's sync'd with the ECU when the timing is locked (for syncing)... I've heard stories where Haltech E11s going nuts and the triggers angles magically get corrupted.

If it's whacked, I suggest going back into your tune and seeing if the trigger angles are correct.

I have spare crank angle sensor if needed from my GTRs. When you say checked plugs, you do mean tried another set of plug right. They are pretty old plugs for coppers. What heat range for your R33 gts-t as any colder than a 6 and you will foul them on rich tunes like you've got. 10:1 at idle is way too rich mate. Also check your actual MAP sensor is working correctly. I assume you can check the voltages within the ECU are normal. I had an Apexi one die this year on my 32

11 hours ago, BK said:

I have spare crank angle sensor if needed from my GTRs. When you say checked plugs, you do mean tried another set of plug right. They are pretty old plugs for coppers. What heat range for your R33 gts-t as any colder than a 6 and you will foul them on rich tunes like you've got. 10:1 at idle is way too rich mate. Also check your actual MAP sensor is working correctly. I assume you can check the voltages within the ECU are normal. I had an Apexi one die this year on my 32

Not 21,000KMs i meant actually less than 30KM's. Yes checked map sensor and heat range was 6, had 5s in previously and am waiting for some new parts to arrive. Ive put 5s back in it (new ones) as im under that feeling that they were barely managing with a 5 heat range. Ill keep it posted on re start.

  • 10 months later...
1 hour ago, KiwiRS4T said:

Which sensor? Also believe there were a lot of fake Sard FPRs around...- Running OK now? What are you making with the 3582?

Air temp intake temp (after intercooler). Nah genuine SARD and havnt had figures yet. Car has been parked up since after Red Center Nats #02, bought a house and a motorcycle and at long last got of my ass to drain the tank of old fuel before i send it south next month.

Yes thats a long ass siphon hose

20170612_134028.jpg

Edited by KittoRB25
Grammar
  • 2 years later...
On 12/06/2017 at 8:50 PM, KiwiRS4T said:

Which sensor? Also believe there were a lot of fake Sard FPRs around...- Running OK now? What are you making with the 3582?

Reviving a necro thread.

went go a safe tune at 18psi and walked away with 322 RWKW on 98

Edited by KittoRB25
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...