Jump to content
SAU Community

Recommended Posts

Looking for a 5 bolt 3.9 diff (locked, LSD, open, what ever) to trade for my locked 4.11 diff.

 

Diff is very healthy, was welded by a professional shop and has NO bearing noise or anything.

 

Only trading because I want to try a different ratio.

Fair enough

Back when I used to diff swaps people often expected a marked difference from this kind of ratio swap and were always a little disappointed with the end result, as opposed to those who had gone to something like a 3.7 etc.

I just put a s15 auto vicous lsd diff in my r33 diff so went from 4.1:1 to 3.9:1
To drop revs alil to hopefully save fuel on highway driving
Plus my old diff had alot of backlash

I felt a difference definately noticable as it use to be alot more rev snappy and 2nd gear stayed in the powerband alot easier
At 80km now it a bit under 2krpm now in 5th gear not sure what it was with the std diff
Had to also get 6 bolt driveshafts as the skyline halfshafts didnt fit in the s15 diff

Looking for a 5 bolt 3.9 diff (locked, LSD, open, what ever) to trade for my locked 4.11 diff.

 

Diff is very healthy, was welded by a professional shop and has NO bearing noise or anything.

 

Only trading because I want to try a different ratio.


Your diff abs or non ?
4 hours ago, hy_rpm said:

I just put a s15 auto vicous lsd diff in my r33 diff so went from 4.1:1 to 3.9:1
To drop revs alil to hopefully save fuel on highway driving
Plus my old diff had alot of backlash

I felt a difference definately noticable as it use to be alot more rev snappy and 2nd gear stayed in the powerband alot easier
At 80km now it a bit under 2krpm now in 5th gear not sure what it was with the std diff
Had to also get 6 bolt driveshafts as the skyline halfshafts didnt fit in the s15 diff

cbf looking for the ratios and rolling diameter to do a calculation, but it'd be all of ~150rpm difference IMO

cbf looking for the ratios and rolling diameter to do a calculation, but it'd be all of ~150rpm difference IMO





Hey mate guess is a guess
Im talking about real life experience
Have you even tried and tested it
No so keep you comments and guesses to yourself


Just tryed it on the freeway to work
At 100km used to to sit at 3000rpm with the 4.11
Now with the 3.9 sits at 2500-2600rpm at 100km both in 5th gear so more like a 4-500rpm difference
3 hours ago, hy_rpm said:

Hey mate guess is a guess
Im talking about real life experience
Have you even tried and tested it
No so keep you comments and guesses to yourself

Yes, as previously stated, I used to fit diffs and do ratio swaps for customers. The problem with your real world experience is that it's also based on a guess - your recollection - and can be wrong too...and it is. Not only does this lead the OP to believe they'll have some drastic difference in engine speed, but anyone searching the topic may make the same mistake.

1 hour ago, hy_rpm said:

 

 

 

 


Just tryed it on the freeway to work
At 100km used to to sit at 3000rpm with the 4.11
Now with the 3.9 sits at 2500-2600rpm at 100km both in 5th gear so more like a 4-500rpm difference

 

 

 

 

3000rpm / 4.11 = 730

730 x 3.9 = 2847rpm

Looks like my guess wasn't far off.

That's one magic diff mate.

On 8/7/2016 at 6:10 PM, hy_rpm said:


Your diff abs or non ?

Non ABS.

 

I've had a 3.9 diff before. I prefer it marginally longer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...