Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Right...did you want to know specifically which wheels from the Nissan range will fit?

There is a HyperRev issue in fact 2 for the Stagea which also looks at what kind of wheels you can fit to the Stagea. Unfortunately there isn't much in terms of tuning, as they are pretty much the same as Skylines...engine wise. If I happen to go pass a newagent I can take a squizz for you, anything specific you wanted to know about the wheels specs?

Right...did you want to know specifically which wheels from the Nissan range will fit?

There is a HyperRev issue in fact 2 for the Stagea which also looks at what kind of wheels you can fit to the Stagea.  Unfortunately there isn't much in terms of tuning, as they are pretty much the same as Skylines...engine wise.  If I happen to go pass a newagent I can take a squizz for you, anything specific you wanted to know about the wheels specs?

I'll take any info you can dig up, thanks :P

Thanks Duncan, I wonder if they will let me drive it around with a few sets of loan wheels and tyres for a couple of days each? Just to make sure they don't rub anywhere and that the handlig feels OK, they don't make lots of noise, some tyres simply don't work on some cars etc. :)

The clearance testing may be tricky though, because I won't have set the heights up and maybe not upgraded the brakes. Golly, gosh I would hate to buy a set of wheels that fitted today and then find when I lowered it and put the bigger brakes on those nice new wheels didn't fit. :thumbdwn:

I'll bet that would never happen.......... :jk:

one of the guys on SWAT reccomends...

フロントが235/45/17 8J オフセット+45

リアが235/45/17 9J オフセット+44です。

or should I say,

Front: 235/45/17 by 8". Offset +45

Rear: 235/45/17 by 9". Offset +44

Also... one of the other guys on their bbs runs...

Summer

Front: WORK VS-SS 18 by 7.5 +15 225/40

Rear: BBS LM 18 by 8" +38 FALKEN ZIEGS 235/40

Winter:

SSR integral 17 by 9" +38 MZ03 235/45

When using the 17's he uses 20mm spacers at the front and 26mm spacers at the back

Extreme Winter:

MT-14 15 by 6.5" +38

26mm spacers all around

Do the RS260's run different offset than the RS FOUR versions?

Seems like there are a few fairly different offset specs flying around this thread!

I pick up my 260 tomorrow..it has genuine autech wheels will find out then

saw the car today at the docks......just waved at it ...fark :pissed:

Had a look at what Rays reccomend with their wheels and got this:

STAGEA WC34 1670 +33 205/55R16 1670 +33 205/55R16

STAGEA WC34 1785 +30 225/45R17 1785 +30 225/45R17

STAGEA WC34 1885 +30 225/40R18 1885 +30 225/40R18

STAGEA C34 1780 +38 225/45R17 1780 +38 225/45R17

STAGEA C34 1880 +32 225/40R18 1880 +32 225/40R18

Had a look at what Rays reccomend with their wheels and got this:

STAGEA WC34 1670 +33 205/55R16 1670 +33 205/55R16  

STAGEA WC34 1785 +30 225/45R17 1785 +30 225/45R17  

STAGEA WC34 1885 +30 225/40R18 1885 +30 225/40R18  

STAGEA C34 1780 +38 225/45R17 1780 +38 225/45R17  

STAGEA C34 1880 +32 225/40R18 1880 +32 225/40R18

Am I reading this right, the widest tyre is a 225? :headspin:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...