Jump to content
SAU Community

Recommended Posts

So I've had my R33 for a few months now and I've recently been having boost control issues. I have Greddy profec B Spec II and its acting very strangely. It drives fine and holds boost until it hits peak boost (14psi) then it will no longer make any boost. The display says it's making around 1psi. But then after leaving it for a while it will work fine again, rinse and repeat. Is it the solenoid sticking open? Any help would be great. 

Cheers 

Link to comment
https://www.sau.com.au/forums/topic/466339-boost-control-issue/
Share on other sites

Well if it works fine with the boost controller unpowered then the issue definitely lies there. The thing is, if it's switched off, the lowest the boost can go is wastegate spring pressure and i would expect that to be between 5-7 psi. You said when it plays up your only getting 1 psi. Since you have an aftermarket split dump, i would definitely check the flapper opens and closes smoothly and doesn't get caught open. Some of the split dumps have a reputation for causing this. Wont take long to check and rule it out as a possibility if it's all good. Cheers.

You're going to have to determine why it's sticky. Most probably it is fouling the inside edge of the dump pipe. You will have to take the dump off to take a look and either dremel it for clearance or replace it with a bell mouth dump. The other possibility is the flapper mechanism itself is faulty and sliding in and out. Pull the dump, diagnose and then take action. Cheers.

No probs. You could also try spraying some wd40 or similar on the shaft of the flapper and open and close it quite a few times and see if that frees it up before you go pulling shit off. I use to have a turbo on an old car of mine that had a sticky gate and doing that would remedy it for a few months. Give it a shot, can't hurt. Good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...