Jump to content
SAU Community

Recommended Posts

R33 wheel fitment

Hey guys been doing some reading and cant get a definite answer, wanted to know if 

17x9.5 with -20 offset 

Will fit inside standard gaurds if they get pumped/rolled, was trying to figure if they wuld or not before i order them

Thanks in advance

Edited by Beauc32
Link to comment
https://www.sau.com.au/forums/topic/466479-r33-gtst-wheel-fitment/
Share on other sites

no way they'll fit

-20 is way off

+30 is the best offset

they'll be 20mm outside the guards and that's rolled and flared

I have 18 x 9.5 + 30 all round

Dead flush with rolled and flared guards

Front rims hit the control arms a bit, I took out some with an angle grinder.

There's a sticky wheel offset thread..

P9230021.JPG

Edited by conan7772
  • Like 1
On Thursday, August 25, 2016 at 9:21 PM, conan7772 said:

no way they'll fit

-20 is way off

+30 is the best offset

they'll be 20mm outside the guards and that's rolled and flared

I have 18 x 9.5 + 30 all round

Dead flush with rolled and flared guards

Front rims hit the control arms a bit, I took out some with an angle grinder.

There's a sticky wheel offset thread..

P9230021.JPG

f**k that sucks guess i better look for different wheels aha 

Cheers for the help ??

  • 3 weeks later...

My old 1994 R33 GTST Coupe  I got 18 x 8.5 on the front and 18 x 9.5 on the back with zero rolling or offset.

The front rims though were that close to the brake caliper , no more room left...

 

 

229265_7008947250_1209_n.jpg

226490_7008997250_5322_n.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...