Jump to content
SAU Community

Recommended Posts

1994 R32 GTR $12,000 (needs work)

My priorities have shifted to a house so I'm putting my R32 GTR up for sale. 

Good points: 
1994 build, imported 2008, I'm the second Australian owner 
Silver
More or less standard, just 3" exhaust and ICS coilovers 
Fairly clean car, straight underneath 
A/C works, clock works 
Recently serviced, including new Splitfire coil packs 
Engine was replaced at some point in Japan with a R33 block (engine number RB26075xxx) 

Bad points: 
Engine is noisy when warm, assume spun bearing (still holds oil pressure) 
Dash has bubbles, drivers seat is worn, drivers doorlock is broken (has central locking/immobiliser so never bothered fixing)
Paint is showing its age on roof and spoiler, small dent in rear LHS quarter 
120,000kms on odometer (export certificate suggests closer to 190,000kms) 

$12,000 cash as-is where-is, no rego/rwc/plates.
Car is in Elsternwick in Melbourne, happy for inspections most weekday nights.

Needs some work but a good base for a project - I've been very honest with the condition. Firm on price. If it doesn't sell for this much, I'll garage it for a few years and come back to it. 

If you want them, comes with a few spares: 
R33 GTR wheels (painted badly, one needs to be repaired) 
Early R32 RB26 block (broken valve guide has gone through it but apparently otherwise okay)
Replacement drivers side window regulator 

1.jpg

2.jpg

3.jpeg

1.jpg

2.jpg

3.jpeg

Link to comment
https://www.sau.com.au/forums/topic/466492-sold-1994-r32-gtr-12000-needs-work/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...