Jump to content
SAU Community

[SYD] FS: HKS 2835 Pro S turbo, Apexi PowerFC, Z32 AFM, Greddy Profecb II boost controller, and more..

Aleckr33
 Share

Recommended Posts

Aleckr33 Rising Star

Aleckr33

Posted
Posted

[SYD] FS: HKS 2835 Pro S turbo, Apexi PowerFC, Z32 AFM, Greddy Profecb II boost controller, and more..

Hi everyone, i have some parts that will be coming off my car shortly, so ALL parts are currently still on the car for about a week... if you are interested PM me and we can work something out.

Item 1:
Genuine HKS 2835 pro S turbo .68 rear with dump
$1500

Item 2:

Apexi PowerFC with hand contoller to suit RB25DET Series 2 (might suit Series 1 not sure)

$1000

Item 3:

Greddy Profec b II Boost controller

$200

 

Item 4:

Coolingmist water methanol injection kit with tank and in cabin gauge 

$200 

 

item 5:

RB25DET Standard exhaust manifold

$80

 

Item 6:

Z32 Air flow meter with plug

$150

 

I will have more to come so i will keep updating this post.

 

All parts are located in Sydney, Liverpool. Pick up preferred. Thanks.

 

hugh jaynous Contributor

hugh jaynous

Posted
Posted

Just wondering if you'd be keen on some postage to Canada? Looking at that manifold. Thanks! 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Butters
      No engine fan = quieter getrag ???

      By Butters · Posted

      Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...