Jump to content
SAU Community

NM35 MAF pin outs

cad

By cad,
in Four Door Family & Wagoneers

 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

You might struggle, they are completely different in operation. If you are planning to tune the M35 as a standalone you can just run new wires to the Z33? I would go Z32 or VQ35 personally. 

How are you planning to fix the airflow curve if not tuning? 

cad Collaborator

cad

Posted
  • Author
Posted

Thanks for the reply Scotty. I bought of Yahoo Japan a series 3 nismo reset ECU which comes with a Z33 AFM and housing along with a patch lead. The plug which matches my sensor has had the wiring and pins ripped out so i dont know how to match it to mine. The system came out of a working nm35 stagea so i presume it will operate correctly on mine. Two wire have been joined on the Z33 wiring harness one of which is an earth.I have power and the sense signal wire but the car wont idol. Any help would be appreciated.

West Grand Master

West

Posted
Posted
3 hours ago, cad said:

All done Z33 air sensor done and series 3 sports reset seems to be working as it should. Take it for a run tonight and see what happens.

Awesome, keep us up to date. While they're not tune-able, its still interesting to see what it does and it has to be good.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...