Jump to content
SAU Community

Recommended Posts

Depends what you asked for

http://www.kudosmotorsports.com/catalog/water-pass-heater-hose-piece-nissan-skyline-p-1653.html

From the Kudos website for the R32 GTR. $312 for the genuine Nissan 10 hose kit

 

But if your OCD like me - there is also air hoses (2 or 3) and the radiator hoses upper and lower ($150). and for good measure at a great price is the metal water tube (under plenum) for $40 and water tube on the upper timing case.

 

2 minutes ago, Sinista32 said:

Depends what you asked for

http://www.kudosmotorsports.com/catalog/water-pass-heater-hose-piece-nissan-skyline-p-1653.html

From the Kudos website for the R32 GTR. $312 for the genuine Nissan 10 hose kit

 

But if your OCD like me - there is also air hoses (2 or 3) and the radiator hoses upper and lower ($150). and for good measure at a great price is the metal water tube (under plenum) for $40 and water tube on the upper timing case.

 

I reckon it would be worth changing all of my hoses as the car has been sitting in the weather non running for 10 years, I will show you what kudos quoted me

2380_2017-03-27.pdf

That's good, a good price. Probably remove the SAMCO upper and lower radiator hose set for $128 as your quote already has the OEM set in it.

Grab the metal under plenum tube for $38 and water tube on the upper timing case. Tendency also to either rust or leak.

You have all the blow bye hoses included too.

So yeah, a very good price. :thumbsup:

Edited by Sinista32
Just now, Sinista32 said:

That's good, a good price. Probably remove the SAMCO upper and lower radiator hose set for $128 as your quote already has the OEM set in it.

You have all the blow bye hoses included too. So yeah, a very good price.

Cheers buddy, appreciate it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...