Jump to content
SAU Community

Damaged RB30 Block Repairs

Steve85

By Steve85,
in General Maintenance

 Share

Recommended Posts

Steve85 Mentor

Steve85

Posted
Posted
Damaged RB30 Block Repairs

Hi all,

I'm helping a friend rebuild a VL Calais. Long story short we bought the car for $2500 as a bunch of pieces and a rolling shell. Most of the car was there and we have managed to put it all back together. I should add that we are by no means mechanics, so please excuse my ignorance where it may appear.

We have managed to start the car and it does move under its own power after several months of rebuilding it, however, one of the exhaust manifold studs was bent and had been poorly re-tapped. Initially we believed this would not be an issue, however, it leaks radiator coolant from the re-tapped stud area (we just left the exhaust off the car for initial tests). 

We have since learned that this cannot be repaired quite as simply as we had hoped and the block may need serious work to be any use to us. I believe that there may be coolant leaking into cylinder six. There is no water in the oil (we've checked twice). Obviously this is an issue and we are in the process of stripping and pulling the engine out for reconditioning. The coolant absolutely pours out of the exhaust port of cylinder six when the engine is running. I'd suggest it could empty the coolant from the car within 15 minutes if left to run. 

My query here is, in the event that we pull the engine for re-condition and cylinder six is in good condition, is it going to be possible to repair the block of the engine?

We could simply have someone re-work the block and re-tap the stud, but does anyone know the effect that might have on the water path through the block? I'm concerned that if we attempt a repair we will re-direct the coolant path into the cylinder itself or some other area where we don't want coolant.

Can anyone offer their opinions on this matter or does anyone have experience with this type of problem? (Pictures to follow).

Link to comment
https://www.sau.com.au/forums/topic/471080-damaged-rb30-block-repairs/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

well the good news is that the exhaust ports and their studs go into the head, not the block.....which means you probably have a perfectly good (and valuable) rb30 block.

the single cam rb30 head is probably worth about $3 including postage so you may be able to just swap it for another if you are trying to get it going cheaply.

 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So....knowing that I have a problem with power steering temps on track and another Wakefield day booked in next Friday, I've done the obvious thing They are very reasonably priced at $1650, considering they are a big monotube shock, double height adjustable (don't have to change pre-load to change ride height), one way adjustable damping and standard sized and customisable springs if you want something other than what comes with them. They come with 9kg/mm front and 4.5kg/mm front and I went with that as a starting point because I'll add adjustable sway bars too https://justjap.com/products/bc-racing-coilover-kit-ds-ds-infiniti-q50-v37-14-current#description Unfortunately they didn't come with rear strut tops so I've re-used the factory ones which was a bit of a pain. Also, the adjuster for the rear shock will be an absolute nightmare to get at, and while there are extensions in the kit I can't see any way you can actually attach or use them
    • Duncan
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By Duncan · Posted

      I also had 2 bulbs blow at once, years ago in the stagea. made for a fun drive home. The issue was the voltage regulator had failed in the alternator and it was giving 15+ volts. Really, I was lucky all that was fried were the headlight bulbs. So, I'd suggest you check the voltage across your battery terminals with the car running and warmed up. Yes, you will need a multimeter to do so, sorry.
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Good work to think to check that, and thanks for coming back to post up the outcome.
    • Duncan
      98 R34GTT 4k engine stumble

      By Duncan · Posted

      Given it happened suddenly, and when you come on boost, I'd check all your inlet - hose clamps in place and no split rubber or silicone hoses. Even the hard to get to ones near the intercooler. It's possible air that went past the air flow meter is being dumped out a big hole.
×
×
  • Create New...