Jump to content
SAU Community

Greddy Emanage rb25det

Chris33
 Share

Recommended Posts

Chris33 Apprentice

Chris33

Posted
Posted
Greddy Emanage rb25det

Hii guys, I've a serious problem with my greddy e-manage Ultimate for r33 gtst s1. In principle, I've my modifications made to lack of the ECU, today, in the workshop they haven't even been able to start the car because we were trying to configure base map which greddy.com doesn't have. The problem is that it doesn't turn on : / Im sad because it is only fit the ECU and do not want to start. I have adjusted the main settings such as number of cylinders, engine, type, etc., but still not starting. Is there anything that is left behind? please help. Thanks mates!!! 

Mods: gtx3076r DBB, exhaust manifold 6boost top mount, injectors 550 Nismo size, ex Gate turbosmart to 38 screamer,exhaust line 3", front mount intercooler, wallbro fuel pump, filter k&N, sensor map not afm. ( i get with Ecu greddy). 

Link to comment
https://www.sau.com.au/forums/topic/471391-greddy-emanage-rb25det/
Share on other sites
hardsteppa Grand Master

hardsteppa

Posted
Posted

Emanage doesn't have base map because you still run off factory ecu; that IS the base map. 

I have read they can fry easily though, something about being put on the vtec setting, when used on non vtec motors?

So the unit itself doesn't even power up, is that your issue?

  • Like 1
Chris33 Apprentice

Chris33

Posted
  • Author
Posted

Thanks for replying so quickly Hardsteppa, you're right, being piggy back used the base map to remap the ECU with the greddy, anyway, we could not start the engine yet. We have put the initial settings without result. I have seen in the greddy manuals something remove the upper lid of the ECU and regulate there something, but I am not sure. know something ? How can I tune my ecu to boot? Thanks again.

  • 3 weeks later...
Chris33 Apprentice

Chris33

Posted
  • Author
Posted

Hi guys!!!! :( , Yes, thank you very much for the link, it has been very helpful to me and forgives the delay. But we have not yet been able to remove the Afm, I found an airflow output table that needs to fill in the afm values at all revolutions and copy them to airflow output map where it is Greddy pressure sensor, but it does not work. Can someone tell me how I can remove it completely?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...