Jump to content
SAU Community

Recommended Posts

RB25Neo/30

A bit stuck, done a search but just confusing the f**k out of me. 

Got an RB25Neo/30 in my R32. Using the rb20 loom, got a coil conversion loom and rewired the injectors. 

When it comes to the ECU, what can I actually run? From what I have worked out there is a GTRLink that I can use as it's the same ecu plug. 

Found a Vipec V88 for a neo, that won't plug in though will it? How do I get around this as it's a good price.

 

cheers.

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/
Share on other sites

Hi mate

you only have 2 sort of easy choices here.

1. Remove the loom, and install a RB25 NEO loom to run with the Neo Vipec.
2. Get a GTRLink / Vipec. These fit all GTR models, and the R32 and R33 GTS-T. 

Any other way will only be a huge bitch.

You could get yourself a brand new wiring specialties Neo harness. Would cost about $1k but then you have a new loom. 

Personally, since later model Neos have fairly new looms in then, just grab a factory one of those nice and cheap

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849159
Share on other sites

1 hour ago, The Mafia said:

Hi mate

you only have 2 sort of easy choices here.

1. Remove the loom, and install a RB25 NEO loom to run with the Neo Vipec.
2. Get a GTRLink / Vipec. These fit all GTR models, and the R32 and R33 GTS-T. 

Any other way will only be a huge bitch.

You could get yourself a brand new wiring specialties Neo harness. Would cost about $1k but then you have a new loom. 

Personally, since later model Neos have fairly new looms in then, just grab a factory one of those nice and cheap

When you say get a GTRLink/Vipec which Vipec is this that will work?

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849175
Share on other sites

Vipec and Link are the same thing / same hardware. Vipec is actually gone now, absorbed back into Link. 

Vipec "V" series = Link G4
Vipec "i" series = Link G4+

You want the model of vipec or link that fits the GTR. It also fits the RB20. (It's a one ECU fits all)

The GTRLink / GTRVipec fits everything except for the Neo as that has a different plug.

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849180
Share on other sites

28 minutes ago, The Mafia said:

Vipec and Link are the same thing / same hardware. Vipec is actually gone now, absorbed back into Link. 

Vipec "V" series = Link G4
Vipec "i" series = Link G4+

You want the model of vipec or link that fits the GTR. It also fits the RB20. (It's a one ECU fits all)

The GTRLink / GTRVipec fits everything except for the Neo as that has a different plug.

Damn this one fits a neo, that's a no go.

 

Thanks heaps mate.

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849182
Share on other sites

There is no RB25 Nistune so if you have an RB20 Nistune that will work although it will not control your VCT.

If you get a Neo ecu and loom you can get a GTT  LinkECU to put inside the Neo case which would be ideal...it can control your VCT and with a solenoid better control boost.

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849434
Share on other sites

10 hours ago, Griffin said:

I have the same dilemma with a rb20de cefiro. It's auto and I want to keep it auto. Can I use a link rb26rb20 plugin? Do they have a built-in map sensor to do away with afm?

I don't know where the auto ecu is on your cefiro. If it is in the main engine ecu then no you will not be able to use the GTR Link. Why don't you get a wire in Link instead and yes you can use a map sensor with it.

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849627
Share on other sites

47 minutes ago, KiwiRS4T said:

I don't know where the auto ecu is on your cefiro. If it is in the main engine ecu then no you will not be able to use the GTR Link. Why don't you get a wire in Link instead and yes you can use a map sensor with it.

Do you know how to find out? Will it be in the same location behind kick panel where main ecu is? 

I have an rb25 det manual loom and ECU, should I fit that and get a manual valve body for the auto to do away with the auto electrics? Then I could fit a plugin ECU . 

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7849638
Share on other sites

  • 3 weeks later...

I'm running a 2530 neo in my r32 gts4, basically had to do a small amount of soldering for tps and idle valve and coil harness. Add in a wire for vct
Can use pretty much any plug in ecu for r33 r32 gtst or gtr. Some need an injector pin swaped around and if using GTr or 32 gtst ecu need a way to control vct, so rpm window switch or if using an r32 gtst nistune then use the feature pack and it let's you control it like stock
I use an adaptronic select on mine personally.

Link to comment
https://www.sau.com.au/forums/topic/471974-rb25neo30/#findComment-7852430
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...