Jump to content
SAU Community

Recommended Posts

Hey guys,

After some input.

Basically I've just sold my cefiro I'd built over the last 6 years. Built as a street car that I could take drifting. RB20, 240rwkw, laggy. No air con, loud, etc etc.

Maybe my age is catching up with me, haha, but didn't really enjoy it much lately, hence the sale.

I'd planned to replace it with a R34 sedan, keep the aircon, and just do the basics, (coil overs, diff, basic engine power mods for around 200rwkw).

My "daily" at the current time is a 97 series 2 R33 sedan, turbo auto.

Never really that into it, bought it off a mate when we needed a new run around, basically stock. Goes ok, but on the standard struts (with lowering springs) was never that inspiring to drive.

Popped that up for sale, and started looking for a R34. 

Test drove one, and this is where I started getting confused. I think I may have had it in my head that  R34 would be noticeably better than our 33, well, the one I drove was not! Ha. Interior was a bit nicer, but no more room (less in the rear seats) than the 33. Chassis wise it felt very similar, and even power was no noticeable difference. TBH I think the r34 I drove wasn't running very well, our 33 feels quicker.

This was turbo auto too (budget doesn't stretch to a factory manual, planing to convert an auto).

 

Anyway, starting to think I might be better keeping the 33 sedan and modding that, as opposed to buying an R34.

 

Has anyone else made the switch from a R33 to a R34? Did you notice a sizeable difference between the two? 

Link to comment
https://www.sau.com.au/forums/topic/472179-r33-to-r34-upgrade/
Share on other sites

The r33 and 34 suspension are identical as are the auto transmissions, to be honest i couldn't see the point in upgrading (more like side stepping) from a 33 to a 34. 

Ive driven both and despite the claimed extra 20kw I can't tell the difference and it's only really cosmetically that they are all that different from each other

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...